
TTP/C-C2 Communication Controller
– Preliminary Data Sheet
AS8202
Rev. 1.0, October 2000
Page 5 of 5
Electrical Specifications
Absolute Maximum Ratings (Non Operating)
SYMBOL PARAMETER
VDD
DC Supply Voltage
V
in
Input Voltage on any Pin
I
in
Input Current on any Pin
T
strg
Storage Temperature
T
sold
Soldering Temperature
t
sold
Soldering Time
H
Humidity
ESD
Electrostatic Discharge
1. 300 oC all ceramic packages and DIL plastic packages, 260 oC for surface mounting plastic packages
Note:
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may effect device reliability (e.g. hot carrier
degradation).
MIN
-0.3 V
- 0.3 V
-100 mA
-55 oC
5 %
1000 V
MAX
5.0 V
VDD + 0.3 V
100 mA
150 oC
260 oC
10 sec
85 %
NOTE
25°C
1)
Reflow and Wave
HBM: R = 1.5 k , C = 100 pF
Recommended Operating Conditions
PARAMETER
DC Supply Voltage
Circuit Ground
Static Supply Current
Operating Supply Current
SYMBOL MIN
VDD
VSS
IDDS
IDD
TYP
3.3 V
0.0 V
700
μ
A
45 mA
MAX
3.6 V
0.0 V
800
μ
A
56 mA
NOTE
1)
2)
fCLK = 40 MHz, VDD = 3.6 V
3)
oscillator pins xin0, xout0
oscillatpr pins xin1, xout1
3.0 V
0.0 V
----
----
Main clock frequency
Bus Guardian clock
frequency
Ambient Temperature
CLK
CLK2
5 MHz
4 MHz
20 MHz
16 MHz
Ta
-40 oC
+125 oC
1)
1. The input and output parameter values in this table are directly related to ambient temperature and DC supply
voltage. A temperature range other Ta
min
to Ta
max
or a supply voltage range other than VDD
min
to VDD
max
will
affect these values and must be evaluated extra.
2. Static supply current IDDS is exclusive of input/output drive requirements and is measured at maximum VDD
with the clocks stopped and all inputs tied to VDD or VSS, configured to draw minimum current.
3. Operating current is exclusive of input/output drive requirements and is measured at maximum VDD and
maximum clock frequency 40 MHz.
DC Characteristics and Voltage Levels
CMOS I/O levels for specified voltage and temperature range unless otherwise noted.
Inputs Pins
Pin Name
Vil
Vih
max
min
All inputs and IO pins
without pull-up/down
VDD
VDD
Inputs with pull-up
30%
VDD
VDD
Inputs with pull-down
30%
VDD
VDD
1. Iil ist tested at VDDmax and Vin = 0
2. Iih ist tested at VDDmax and Vin = VDDmax
3. CMOS input levels are in percentage of VDD, for pull-up/down refer to pin description above.
Iil (1)
min
NA
Iih(2)
min
NA
NOTE
CMOS input (3)
max
-1.0
μ
A
-160
μ
A
NA
max
1.0
μ
A
NA
30%
70%
70%
-50
μ
A
NA
NA
CMOS with
pull up (3)
CMOS with
pull down (3)
70%
30
μ
A
160
μ
A