- 您現在的位置：買賣IC網 > PDF目錄381310 > AS5043 (AUSTRIAMICROSYSTEMS AG) 10-bit (SSI, analog) PDF資料下載
參數資料
| 型號： | AS5043 |
| 廠商： | AUSTRIAMICROSYSTEMS AG |
| 元件分類： | 同步/旋轉傳感器 |
| 英文描述： | 10-bit (SSI, analog) |
| 中文描述： | 可編程360Σ式磁角編碼器的絕對小型工業和模擬輸出 |
| 文件頁數： | 18/36頁 |
| 文件大?。?/td> | 719K |
| 代理商： | AS5043 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AS5043
Data Sheet – Analog Readback Mode
www.austriamicrosystems.com
Revision 1.80
18 – 36
13 Analog Readback Mode
Non-volatile programming (OTP) uses on-chip zener diodes, which become permanently low resistive when subjected to
a specified reverse current.
The quality of the programming process depends on the amount of current that is applied during the programming
process (up to 130mA). This current must be provided by an external voltage source. If this voltage source cannot
provide adequate power, the zener diodes may not be programmed properly.
In order to verify the quality of the programmed bits, an analog level can be read for each zener diode, giving an
indication whether this particular bit was properly programmed or not.
To put the AS5043 in Analog Readback Mode, a digital sequence must be applied to pins CSn, PROG and CLK as
shown in Figure 15. The digital level for this pin depends on the supply configuration (3.3V or 5V; see section 1, page 5).
The second rising edge on CSn (OutpEN) changes pin PROG to a digital output and the log. high signal at pin PROG
must be removed to avoid collision of outputs (grey area in Figure 15).
The following falling slope of CSn changes pin PROG to an analog output, providing a reference voltage V
ref
, that must be
saved as a reference for the calculation of the subsequent programmed and unprogrammed OTP bits.
Following this step, each rising slope of CLK outputs one bit of data in the reverse order as during programming.
(see Figure 15: Output Range OR0 and -1 , ClampMdEn, RefExtEn, FB_IntEn, Z0…Z9, ccw)
During analog readback, the capacitor at pin PROG (see Figure 12) should be removed to allow a fast readout rate.
The measured analog voltage for each bit must be subtracted from the previously measured V
ref
, and the resulting value
gives an indication on the quality of the programmed bit: a reading of <100mV indicates a properly programmed bit and a
reading of >1V indicates a properly unprogrammed bit.
A reading between 100mV and 1V indicates a faulty bit, which may result in an undefined digital value, when the OTP is
read at power-up.
Following the 16
th
clock (after reading bit “ccw”), the chip must be reset by disconnecting the power supply.
Figure 15: Analog OTP Register Read
Internal
test bit
digital
V
unprogrammed
V
programmed
CSn
CLK
1
16
PROG
ProgEN
OR1
OR0
Analog Readback Data at PROG
OutpEN
t
LoadProg
CLK
Aread
Prog ch anges to Output
V
ref
Power-on-
Reset;
cycle supply
RefExt
EN
Clamp
M dEN
Z6
Z5
Z8
Z7
ccw
Z9
相關PDF資料 |
PDF描述 |
|---|---|
| AS5134 | 360-steps (SSI, PWM, ABI, UVW); Package Type: SSOP-20; Temperature Range: -40 - +140 °C; Resolution: 8,5-bit rotary (360 steps); Automotive Qualification: X; Output Interface: SSI & PWM; Supervised Voltages (IN1): 5,00; Supply Voltage: 4,50-5,50 |
| AS5245 | 12-bit Rotary Position Sensor; Package Type: QFN(5x5)-32; Temperature Range: -40 - +140 °C; Resolution: 12-bit rotary (4096 steps); Automotive Qualification: X; Output Interface: SSI & PWM; Supervised Voltages (IN1): 5,00; Supply Voltage: 4,50-5,50 |
| AS5501 | ER 4C 4#8 SKT RECP BOX |
| AS5502 | Multimode Powerline-Modem |
| AS6UA25616 | 2.3V to 3.6V 256K×16 Intelliwatt low-power CMOS SRAM with one chip enable(2.3V 到 3.6V 256K×16 Intelliwatt 低功耗 CMOS 靜態RAM（帶單片使能）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AS5043 AB | 功能描述:BOARD ADAPTER AS5043 RoHS:否 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AS5043 DB V2 | 功能描述:BOARD DEMO AS5043 RoHS:否 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AS5043 PB | 功能描述:BOARD PROGRAM AS5043 RoHS:否 類別:編程器，開發系統 >> 適配器 系列:- 標準包裝:96 系列:- 模塊/板類型:TQFP 插座模塊 適用于相關產品:- |
| AS5043_1 | 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:Programmable 360 Magnetic Angle Encoder with Absolute SSI and Analog Outputs |
| AS5043-AB | 制造商:ams 功能描述:Magnetic Sensor Development Tools AS5043 Adapter Board |
發布緊急采購，3分鐘左右您將得到回復。