- 您現在的位置：買賣IC網 > PDF目錄381310 > AS5043 (AUSTRIAMICROSYSTEMS AG) 10-bit (SSI, analog) PDF資料下載
參數資料
| 型號： | AS5043 |
| 廠商： | AUSTRIAMICROSYSTEMS AG |
| 元件分類： | 同步/旋轉傳感器 |
| 英文描述： | 10-bit (SSI, analog) |
| 中文描述： | 可編程360Σ式磁角編碼器的絕對小型工業和模擬輸出 |
| 文件頁數： | 17/36頁 |
| 文件大?。?/td> | 719K |
| 代理商： | AS5043 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AS5043
Data Sheet – Programming the AS5043
www.austriamicrosystems.com
Revision 1.80
17 – 36
Internal or external reference
The default DAC reference is the voltage at pin #16 (VDD5V) divided by 2 (see Figure 13). Using this reference, a system
that has an output voltage ratiometric to the supply voltage can be built.
Optionally, an external reference source, applied at pin#9 (DACref) can be used. This programming option is useful for
applications requiring a precise output voltage that is independent of supply fluctuations, for current sink outputs or for
applications with a dynamic reference, e.g. attenuation of audio signals.
0-100% or 10-90% full scale range
The reference voltage for the DAC is buffered internally. The recommended range for the external reference voltage is
0.2V to (VDD3V3 -0.2)V.
The DAC output voltage will be switched to 0V, when the magnetic field is out of range, when the MagInc and MagDec
indicators are both =1 and the MagRngn-pin (#1) will go low.
The default full scale output voltage range is 0-100%*VDD5V. Due to limitations in the output stage of an OP-Amp buffer,
it cannot drive the output voltage from 0-100% rail-to-rail. Without load, the minimum output voltage at 0° will be a few
millivolts higher than 0V and the maximum output voltage will be slightly lower than VDD5V. With increasing load, the
voltage drops will increase accordingly.
As a programming option, an output range of 10-90%*VDD5V can be selected. In this mode, there is no saturation at the
upper and lower output voltage limits like in the 0-100% mode and it allows failure detection as the output voltage will be
outside the 10-90% limits, when the magnetic field is in the “red” range (V
out
=0V, see Table 3) or when the supply to the
chip is interrupted (V
out
=0V or VDD5V).
The unbuffered output of the DAC is accessible at pin #10 (DACout). This output must not be loaded.
12.6 OP-AMP Stage
The DAC output is buffered by a non-inverting Op-Amp stage. The amplifier is supplied by VDD5V (pin #16) and can
hence provide output voltages up to 5V.
By allowing access to the inverting input of the Op-Amp and with the addition of a few discrete components it can be
configured in many ways, like high current buffer, current sink output, adjustable angle range, etc...
Per default, the gain of the Op-Amp must be set by two external resistors (see Figure 13). Optionally, the fixed internal
gain setting (2x) may be programmed by OTP, eliminating the need for external resistors.
12.6.1 Output Noise
The Noise level at the analog output depends on two states of the digital angular output:
a) the digital angular output value is stable
In this case, the output noise is the figure given as V
noise
in paragraph 19.3.6. Note that the noise level is given
for the default gain of 2x For other gains, it must be scaled accordingly.
b) the digital output is at the edge of a step
In this case, the digital output may jitter between two adjacent values. The rate of jitter is specified as transition
noise (parameter TN in paragraph 19.5). The resulting output noise is calculated by:
OPAMP
,
noise
Vout
,
noise
V
V
VDD
360
TN
V
5
+
=
where:
V
noise, Vout
TN
VDD5V
V
noise,OPAMP
= noise level at pin Vout in Vrms
= transition noise (in °rms; see 19.5)
= Supply voltage VDD5V in V
= noise level of OPAMP
(paragraph 19.3.6) in Vrms
12.7 Application Examples
See Application Note AN5043-10 for AS5043 Application Examples.
相關PDF資料 |
PDF描述 |
|---|---|
| AS5134 | 360-steps (SSI, PWM, ABI, UVW); Package Type: SSOP-20; Temperature Range: -40 - +140 °C; Resolution: 8,5-bit rotary (360 steps); Automotive Qualification: X; Output Interface: SSI & PWM; Supervised Voltages (IN1): 5,00; Supply Voltage: 4,50-5,50 |
| AS5245 | 12-bit Rotary Position Sensor; Package Type: QFN(5x5)-32; Temperature Range: -40 - +140 °C; Resolution: 12-bit rotary (4096 steps); Automotive Qualification: X; Output Interface: SSI & PWM; Supervised Voltages (IN1): 5,00; Supply Voltage: 4,50-5,50 |
| AS5501 | ER 4C 4#8 SKT RECP BOX |
| AS5502 | Multimode Powerline-Modem |
| AS6UA25616 | 2.3V to 3.6V 256K×16 Intelliwatt low-power CMOS SRAM with one chip enable(2.3V 到 3.6V 256K×16 Intelliwatt 低功耗 CMOS 靜態RAM（帶單片使能）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AS5043 AB | 功能描述:BOARD ADAPTER AS5043 RoHS:否 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AS5043 DB V2 | 功能描述:BOARD DEMO AS5043 RoHS:否 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AS5043 PB | 功能描述:BOARD PROGRAM AS5043 RoHS:否 類別:編程器，開發系統 >> 適配器 系列:- 標準包裝:96 系列:- 模塊/板類型:TQFP 插座模塊 適用于相關產品:- |
| AS5043_1 | 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:Programmable 360 Magnetic Angle Encoder with Absolute SSI and Analog Outputs |
| AS5043-AB | 制造商:ams 功能描述:Magnetic Sensor Development Tools AS5043 Adapter Board |
發布緊急采購，3分鐘左右您將得到回復。