參數資料
型號: AS2702
廠商: AUSTRIAMICROSYSTEMS AG
英文描述: AS-Interface Slave IC
中文描述: AS - Interface的奴隸集成電路
文件頁數: 7/18頁
文件大小: 119K
代理商: AS2702
AS-Interface Slave IC
AS2702 (SAP4.1)
Rev. C, January 2001
Page 7 of 18
with VSIG > 3V, VUOUT may drop as much as 1V below it’s level
in unloaded condition
Electrolythic and rf filter capacitor in parallel
2
I1RP9SRZHUVXSSO\RXWSXW85
The voltage at U5R is derived from the voltage present at UOUT, as long as UOUT is not
switched off due to overload. In the latter case U5R is derived from an alternative voltage out
of the UOUT voltage regulator, which is more or less similar to VUOUT in non switched off
condition of UOUT. As a result VU5R is not affected by overload condition at UOUT and will
remain.
6\PERO
VU5R
IU5R
CU5R
3DUDPHWHU
Power supply output voltage
Load current
Buffer capacitor
PLQ
4.85
PD[
5.15
1
8QLW
V
mA
nF
100
J2VFLOODWRUSLQV26&DQG26&
The only component to be connected to these pins is a quartz crystal with a resonance fre-
quency of 5.333333 MHz (AS-Interface quartz crystal).
6\PERO
CX2
3DUDPHWHU
Stray capacitance
PLQ
PD[
10
8QLW
pF
K'DWDSRUWSLQV''DQGGDWDVWUREHSLQ'67%Q
Basically data port D3
, …, D0 is designed for bidirectional data transfer out of and into the
slave device. Each data port pin is equipped with both a low-side open-drain output stage as
well as an input stage to this purpose.
Depending on the so called IO-configuration code, written into and stored in the slave device,
each data port pin is individually set to behave as
output, or
output / input, or
input.
The timing of the data transfer is presented in fig. 2.
Strobe signal DSTBn flags and governs the data transfer as follows:
ha) data port pin is set ‘output’:
output data become valid upon the HL-edge of the strobe and will remain so until the next
HL-edge, hence during the entire strobe cycle;
hb) data port pin is set ‘output / input’:
output data become valid upon the HL-edge of the strobe and will remain so until it’s LH-
edge; input data to be valid within a specific time window relative to the HL-edge, after
completion of the strobe’s L-phase;
hc) data port pin is set ‘input’:
相關PDF資料
PDF描述
AS2702-16T AS-Interface Slave IC
AS2702-20T AS-Interface Slave IC
AS29F010-150TC 5V 128K x 8 CMOS FLASH EEPROM
AS29F010-120TC 5V 128K x 8 CMOS FLASH EEPROM
AS29F010-150LC 5V 128K x 8 CMOS FLASH EEPROM
相關代理商/技術參數
參數描述
AS2702/SOIC16-SAMPLE 制造商:AMS 功能描述:AS Series 22.5 to 34 V Surface Mount AS-Interface Slave SOIC-16
AS2702_1 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:AS-Interface Slave IC
AS2702-16 功能描述:異步串行接口 - ASI RoHS:否 制造商:ams
AS2702-16T 制造商:ams 功能描述:IC INDUSTRIAL BUS 16-SOIC
AS2702-16-T 功能描述:IC INDUSTRIAL BUS 16-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA,便攜式音頻/視頻,智能電話 接口:I²C,2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤(4x4) 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2