參數資料
型號： AP603
英文描述： High Dynamic Range 7W 28V HBT Amplifier
中文描述： 高動態范圍7瓦28V的異質結雙極晶體管放大器
文件頁數： 3/14頁
文件大?。?/td> 1182K
代理商： AP603
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
Page 3 of 14 May 2007 ver 1
AP603
High Dynamic Range 7W 28V HBT Amplifier
Application Circuit PC Board Layout
PCB Material: 0.0147” Rogers Ultralam 2000, single layer, 1 oz Cu,
ε
r
= 2.45, Microstrip line details: width = .042”, spacing = .050”
Baseplate Configuration
Notes:
1. Please note that for reliable operation, the evaluation board will have to be mounted to a much larger
heat sink during operation and in laboratory environments to dissipate the power consumed by the
device. The use of a convection fan is also recommended in laboratory environments.
2. The area around the module underneath the PCB should not contain any soldermask in order to
maintain good RF grounding.
3. For proper and safe operation in the laboratory, the power-on sequencing is recommended.
Evaluation Board Bias Procedure
The following bias procedure is recommended to ensure proper functionality of AP603 in a laboratory environment. The sequencing is not
required in the final system application.
Bias.
Vcc
Vbias
Vpd
Voltage (V)
+28
+5
+5
Turn-on Sequence:
1.
Attach input and output loads onto the evaluation board.
2.
Turn on power supply Vcc = +28V.
3.
Turn on power supply Vbias = +5V. At this point, the only current drawn by the device is leakage current (< 25
μ
A).
4.
Turn on power supply Vpd = +5V. Power supply Vcc should now be drawing typical Icq = 160mA.
5.
Turn on RF power.
Turn-off Sequence:
1.
Turn off RF power.
2.
Turn off power supply Vpd = +5V.
3.
Turn off power supply Vbias = +5V.
4.
Turn off power supply Vcc = +28V.
Notes:
1.
Icq can be adjusted with the resistor R2 from the Vpd (+5V) supply and the PIN_VPD (pin14) of the amplifier. Increasing R2
results in a lower Icq. Icq should not be increased above 320mA.
2.
Vpd is used as a reference for the internal active bias circuitry. It can be used to turn on/off the amplifier. Ipd depends on the Icq
quiescent current setting. Ipd can be up to 8mA at a quiescent current setting of 320mA.
3.
Vbias should be maintained fixed at +5V. Ibias will change based on RF input power level. It can be up to 8mA on the AP603.
Ipd vs Icq
0
2
4
6
8
0
100
200
300
400
Icq Setting (mA)
I
Ibias vs Output Power
0
2
4
6
8
22
24
26
28
30
32
Output Average Power (dBm)
I
相關PDF資料
PDF描述
AP603-PCB1960 High Dynamic Range 7W 28V HBT Amplifier
AP603-PCB2140 High Dynamic Range 7W 28V HBT Amplifier
AP603-PCB900 High Dynamic Range 7W 28V HBT Amplifier
AP622 UMTS-band 4W HBT Amplifier Module
AP6 Analog IC
相關代理商/技術參數
參數描述
AP-603 功能描述:AIR FILTRATION PANEL AP-603 制造商:3m 系列:Versaflo?，AP-600 零件狀態:有效 類型:空氣過濾面板 標準包裝:1
AP603-F 功能描述:射頻放大器 800-2200MHz 11.8dB Gain RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
AP603-PCB1960 功能描述:射頻開發工具 1930-1990MHz Brd 12dB Gain RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V
AP603-PCB2140 功能描述:射頻開發工具 2110-2170MHz Brd 12dB Gain RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V
AP603-PCB900 功能描述:射頻開發工具 869-960MHz Eval Brd 17dB Gain RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*