- 您現在的位置：買賣IC網 > PDF目錄375342 > AP160 (AMIC Technology Corporation) ECONOLINE: REC3-S_DRW(Z)/H4,H6 - Safety standards and approval: EN 60950 certified, rated for 250VAV (LVD test report)- Applied for Ul 1950 Component Recognised Certification- 3W DIP Package- 4kVDC & 6kVDC Isolation- Regulated Output- Continuous Short Circiut Protection Auto-Restarting PDF資料下載
參數資料
| 型號： | AP160 |
| 廠商： | AMIC Technology Corporation |
| 英文描述： | ECONOLINE: REC3-S_DRW(Z)/H4,H6 - Safety standards and approval: EN 60950 certified, rated for 250VAV (LVD test report)- Applied for Ul 1950 Component Recognised Certification- 3W DIP Package- 4kVDC & 6kVDC Isolation- Regulated Output- Continuous Short Circiut Protection Auto-Restarting |
| 中文描述： | 8位單片機8KB的檢察官辦公室 |
| 文件頁數： | 9/25頁 |
| 文件大?。?/td> | 677K |
| 代理商： | AP160 |
AP160
Version 0.0
9
AMIC Technology, Inc.
In this mode, two options are selected by bit EXEN2 in T2CON. If EXEN2=0, Timer2 counts up to 0FFFFH and then sets
the TF2 bit upon overflow. The overflow also causes the timer registers to be reloaded with the 16-bit value in RCAP2H and
RCAP2L. The values in Timer in Capture Mode RCAP2H and RCAP2L are preset by software.
If EXEN2=1, a 16-bit reload can be triggered either by an overflow or by a 1-to-0 transition at external input T2EX. This
transition also sets the EXF2 bit. Both the TF2 and EXF2 bits can generate an interrupt if enabled. Setting the DCEN bit
enables Timer2 to count up or down, as shown in Figure 3. In the mode, the T2EX pin controls the direction of the count. A
logic 1 at T2EX makes Timer 2 count up. The timer will overflow at 0FFFFH and set the TF2 bit. The overflow also causes
the 16-bit value in RCAP2H and RCAP2L to be reloaded into the timer registers, TH2 and TL2, respectively. A logic 0 at
T2EX makes Timer 2 count down. The timer underflows when TH2 and Tl2 equal the values stored in RCAP2H and
RACP2L. The underflow sets the TF2 bit and causes 0FFFFH to be reloaded into the timer registers. The EXF2 bit toggles
whenever Timer 2 overflows or underflows and can be used as a 17
bit of resolution. In this operating mode, EXF2 does
not flag an interrupt.
Table 3.
T2MOD (Timer 2 Mode Control Register)
T2Mod Address = 0C9H Reset Value = XXXX XX00B
Not bit addressable
Bit
7
6
5
4
Symbol
-
-
-
-
Symbol
-
Not implemented, reserved for future
T2OE
Timer 2 Output Enable bit.
DCEN
When set, this bit allows Timer 2 to be configured as an up/down counter.
(DOWN COUNTING RELOAD VALUE)
3
-
2
-
1
0
T2OE
DCEN
Function
OSC
C/T2=0
T2 PIN
CONTROL
TR2
C/T2=1
T2EX PIN
12
÷
OVERFLOW
0FFH
0FFH
RCAP2H
RCAP2L
TH2
TL2
TF2
COUNT
DIRECTION
1=UP
0=DOWN
TIMER 2
INTERRUPT
EXF2
TOGGLE
(UP COUNTING RELOAD VALUE)
Figure 3.
Timer 2 Auto Reload Mode (DCEN=1)
相關PDF資料 |
PDF描述 |
|---|---|
| AP160L | Zener Diode; Zener Voltage Typ, Vz:5.1V; Vz Test Current, Izt:20mA; Power Dissipation, Pd:500mW; Package/Case:41-MiniDIP; Leaded Process Compatible:Yes; Mounting Type:Surface Mount; Peak Reflow Compatible (260 C):Yes |
| AP1L2Q | on-chip resistor NPN silicon epitaxial transistor |
| AP1L3N | on-chip resistor NPN silicon epitaxial transistor |
| AP1A3M | on-chip resistor NPN silicon epitaxial transistor |
| AP1A4A | on-chip resistor NPN silicon epitaxial transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AP1601 | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Step-Up DC/DC Converter |
| AP1601M10 | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Step-Up DC/DC Converter |
| AP1601M10A | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Step-Up DC/DC Converter |
| AP1601M10G-13 | 功能描述:開關變換器、穩壓器與控制器 CNVTR BOOST CMOS PFM 800mA 1-5.5V 1.2V RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| AP1601M10G-U | 制造商:Diodes Incorporated 功能描述:CONV DC-DC SGL-OUT STEP UP 10MSOP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。