- 您現在的位置：買賣IC網 > PDF目錄375342 > AP160 (AMIC Technology Corporation) ECONOLINE: REC3-S_DRW(Z)/H4,H6 - Safety standards and approval: EN 60950 certified, rated for 250VAV (LVD test report)- Applied for Ul 1950 Component Recognised Certification- 3W DIP Package- 4kVDC & 6kVDC Isolation- Regulated Output- Continuous Short Circiut Protection Auto-Restarting PDF資料下載
參數資料
| 型號： | AP160 |
| 廠商： | AMIC Technology Corporation |
| 英文描述： | ECONOLINE: REC3-S_DRW(Z)/H4,H6 - Safety standards and approval: EN 60950 certified, rated for 250VAV (LVD test report)- Applied for Ul 1950 Component Recognised Certification- 3W DIP Package- 4kVDC & 6kVDC Isolation- Regulated Output- Continuous Short Circiut Protection Auto-Restarting |
| 中文描述： | 8位單片機8KB的檢察官辦公室 |
| 文件頁數： | 5/25頁 |
| 文件大?。?/td> | 677K |
| 代理商： | AP160 |
AP160
Version 0.0
5
AMIC Technology, Inc.
SYMBOL
ALE/PROG
TYPE
O/I
DESCRIPTIONS
Address Latch Enable is an output pulse for latching the low byte of the address during
accesses to external memory. This pin is also the program pulse input (PROG) during
Programming on-chip OPT EPROM. In normal operation, ALE is emitted at a constant rate of
1/6 the oscillator frequency and may be used for external timing or clocking purposes. Note,
however, that one ALE pulse is skipped during each access to external data memory. If
desired, ALE operation can be disabled by setting bit 0 of SFR location 8EH. With the bit set,
ALE is active only during a MOVX or MOVC instruction. Otherwise, the pin is weakly pulled
high. Setting the ALE-disable bit has no effect if the microcontroller is in external execution
mode.
Program Store Enable is the read strobe to external program memory. When the AP160 is
executing code from external program memory, PSEN is activated twice each machine cycle,
except that two PSEN activations are skipped during each access to external data memory.
External Access Enable. EA must be strapped to GND in order to enable the device to fetch
code from external program memory locations starting at 0000H up to FFFFH. Note, however,
that if lock bit 1 is programmed, EA will be internally latched on reset. EA should be strapped to
VCC for internal program executions. This pin also receives the 12-volt programming enable
voltage (VPP) during programming OTP EPROM.
Input to the inverting oscillator amplifier and input to the internal clock operating circuit.
Output from the inverting oscillator amplifier.
PSEN
O
EA/Vpp
I
XTAL1
XTAL2
I
O
相關PDF資料 |
PDF描述 |
|---|---|
| AP160L | Zener Diode; Zener Voltage Typ, Vz:5.1V; Vz Test Current, Izt:20mA; Power Dissipation, Pd:500mW; Package/Case:41-MiniDIP; Leaded Process Compatible:Yes; Mounting Type:Surface Mount; Peak Reflow Compatible (260 C):Yes |
| AP1L2Q | on-chip resistor NPN silicon epitaxial transistor |
| AP1L3N | on-chip resistor NPN silicon epitaxial transistor |
| AP1A3M | on-chip resistor NPN silicon epitaxial transistor |
| AP1A4A | on-chip resistor NPN silicon epitaxial transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AP1601 | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Step-Up DC/DC Converter |
| AP1601M10 | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Step-Up DC/DC Converter |
| AP1601M10A | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Step-Up DC/DC Converter |
| AP1601M10G-13 | 功能描述:開關變換器、穩壓器與控制器 CNVTR BOOST CMOS PFM 800mA 1-5.5V 1.2V RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| AP1601M10G-U | 制造商:Diodes Incorporated 功能描述:CONV DC-DC SGL-OUT STEP UP 10MSOP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。