參數資料
型號： AND8054
廠商： ON SEMICONDUCTOR
英文描述： Designing RC Oscillator Circuits with Low Voltage Operational Amplifiers and Comparators for Precision Sensor Applications
中文描述： RC振蕩器電路設計低電壓運算放大器和精密傳感器應用比較
文件頁數： 17/28頁
文件大?。?/td> 168K
代理商： AND8054
AND8054/D
http://onsemi.com
17
Voltage Limit Circuits
Automatic Gain Control (AGC) circuits and voltage limit
or bounding circuits are used in oscillators to prevent the
operational amplifiers from saturating and to avoid
amplifier slew rate limitations. Bipolar transistors are
inherently slow in coming out of saturation; therefore, a
limit circuit should be used to prevent a frequency error
when using amplifiers such as the BiCMOS MC33501 or
MC33503. FET transistors do not have the slow recovery
time problem coming out of saturation; however, a limit
circuit should also be used with CMOS operational
amplifiers. The gain of the transistors in a CMOS
operational amplifier such as the NCS2001 will change
when the transistors saturate; thus, a limit circuit is
necessary to prevent an oscillation error.
Limit circuits will also decrease the required time for the
oscillation signal to stabilize at start–up. When an
oscillator’s poles are located exactly on the imaginary axis,
the resulting waveform will be a perfect sinusoidal signal.
To ensure oscillation startup the poles are adjusted to lie
slightly in the right half s–plane causing the signal to grow
exponentially until it is limited by some type of
non–linearity, such as the saturation voltage of the amplifier.
AGC Circuits
Automatic Gain Control (AGC) circuits provide a linear
control of the amplifier gain to produce a constant output
voltage regardless of the level of the input signal. AGC
circuits are usually used in applications where the level of
signal distortion needs to be minimized. AGC circuits are
more complex than limit circuits and usually consist of an
operational amplifier and/or FET that are used as a variable
resistor. An example of an AGC circuit is shown in Figure 17.
V
EE
AGC
Figure 17. FET AGC Circuit
U1
+
–
V
CC
V
IN
V
OUT
Q1
R2
R1
Limit Circuits
Limit circuits are nonlinear circuits, which clamp the
amplitude to a voltage level that is less than the amplifier
power supply voltage. This clamping function will produce
distortion in the oscillator signal. The selection of the
voltage limit circuits is based on the allowable signal
distortion and the simplicity of the circuit. The distortion
level for most sensor oscillator circuits is relatively
unimportant because only the frequency of the signal is
monitored. Also, limit circuits are preferable to AGC
circuits because they require fewer components. Limit
circuits typically consist of a combination of zener diodes,
diodes, and transistors.
相關PDF資料
PDF描述
AND8058 Two New Analog Switches Set Standards for Space Efficiency
AND8058D Two New Analog Switches Set Standards for Space Efficiency
AND8066 Interfacing with ECLinPS
AND8066D Interfacing with ECLinPS
AND8067 NL27WZ04 Dual Gate Inverter Oscillator Increases the Brightness of LEDs While Reducing Power Consumption
相關代理商/技術參數
參數描述
AND8058 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Two New Analog Switches Set Standards for Space Efficiency
AND8058D 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Two New Analog Switches Set Standards for Space Efficiency
AND8066 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Interfacing with ECLinPS
AND8066D 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Interfacing with ECLinPS
AND8067 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:NL27WZ04 Dual Gate Inverter Oscillator Increases the Brightness of LEDs While Reducing Power Consumption
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*