參數資料
型號： AN1077
廠商： Intersil Corporation
英文描述： ISL6244EVAL1 Multi-phase Evaluation Board Setup Procedure
中文描述： ISL6244EVAL1多相評估板安裝程序
文件頁數： 2/16頁
文件大?。?/td> 931K
代理商： AN1077
2
Application Note 1077
What’s Inside
The Evaluation Board Kit contains the following materials:
The ISL6244 EVAL Board
The ISL6244 Evaluation Board document
What is Needed
The following materials will be needed to perform testing:
1 to 2 electronic loads [see note]
– 0-25V @ 15A (+VDC)
– 0-5V @ 5A (+5V)
– 0-12V @ 1A (+12V)
precision digital multi-meters
NOTE: amperage rating of power supplies are determined by
maximum expected loading plus a percentage margin of error
Quick Setup Guide
Step 1:
Set the 0-5V power supply to +5V and place in the
“STANDBY” or “OFF” position. Connect the
positive terminal (+) of the supply to the +5V
terminal J5 and the negative terminal (-) of the
supply to GND J7.
Step 2:
Connect the positive terminal (+) of a DMM to the
+5V terminal J5 and the negative terminal (-) to the
GND terminal J7.
Step 3:
Set the +VDC power supply to +19V and place in
the “STANDBY” or “OFF” position. Connect the
positive terminal (+) of the supply to the +VDC
terminal J3 and the negative terminal (-) of the
supply to GND J4.Connect the load
Step 4:
Connect the positive terminal (+) of a DMM to the
+VDC terminal J3 and the negative terminal (-) to
the GND terminal J4.
Step 5:
Set the 0-12V power supply to +12V and place in
the “STANDBY” or “OFF” position. Connect the
positive terminal (+) of the supply to the +12V
terminal J6 and the negative terminal (-) of the
supply to GND J8.
Connect the positive terminal (+) of a DMM to the
+5V terminal J5 and the negative terminal (-) to the
GND terminal J7.
Connect the positive terminal (+) of the electronic
load to the VOUT terminal J1. Connect the
negative terminal (-) of the electronic load to the
GND terminal J2. Make sure the electronic load is
set to the 0A condition.
Connect the positive terminal (+) of a DMM to the
VOUT test point TP13 and the negative terminal (-)
to the GND test point TP14.
Check to ensure all jumpers and switches are in
their default positions prior to application of power
(refer to“Detailed Description of Jumper Settings”
and “Detailed Description of Switch Settings” ).
Set all power supplies to the “ON” position. LED
CR1 should show Red. Check all DMM displays for
correct voltage levels. Adjust if necessary.
Turn the ENABLE switch SW2 to the “ON” position.
LED CR1 should show Green. The VOUT DMM
should read 1.60V (
±
1%).
At this point the board has been properly powered up.
Normal testing can begin.
Step 6:
Step 7:
Step 8:
Step 9:
Step 10:
Step 11:
NOTE: If you need technical assistance, or other assistance, with
the ISL6244 Evaluation Board, call 1-888-INTERSIL (468-3774).
Detailed Description of Jumper Settings
Detailed Description of Switch Settings
JUMPER
POSITION
FUNCTION
JP1
Shunted
Berg Jumper for VCORE Set Point
JUMPER
POSITION
FUNCTION
SW1
On
ENABLE On-Board Load Transient
Off (default)
DISABLE On-Board Load Transient
SW2
On
ENABLE ISL6244 and ISL6207
Off(default)
DISABLE ISL6244 and ISL6207
相關PDF資料
PDF描述
AN1082 Using the ISL6401 RSLIC PWM Controller Evaluation Board
AN1406 DESIGNING WITH PECL (ECL AT + 5.0)
AN1504 Metastability and the ECLinPS Family
AN1504D Metastability and the ECLinPS Family
AN1568 Interfacing Between LVDS and ECL
相關代理商/技術參數
參數描述
AN-1077 制造商:IRF 制造商全稱:International Rectifier 功能描述:PFC Converter Design with IR1150 One Cycle Control IC
AN10778 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:PCB layout guidelines for NXP MCUs in BGA packages
AN108 制造商:SMSC 制造商全稱:SMSC 功能描述:capacitor Selection for Internal Regulator Output Pins
AN1081 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier
AN1081S 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*