- 您現在的位置：買賣IC網 > PDF目錄364677 > AN-32 TOPSwitch-GX Flyback Design Methodology PDF資料下載
參數資料
| 型號： | AN-32 |
| 英文描述： | TOPSwitch-GX Flyback Design Methodology |
| 中文描述： | 的TOPSwitch - GX系列反激式設計方法 |
| 文件頁數： | 5/16頁 |
| 文件大小： | 134K |
| 代理商： | AN-32 |
AN-32
5
B
12/02
Power supply efficiency,
η
: 0.8 if no better reference data
available. (Refer to AN-29)
Loss allocation factor, Z: If Z = 1, all losses are on the
secondary side. If Z = 0, all losses are on the primary side.
Set Z = 0.5 if no better reference data is available.
Step 2. Choose feedback circuit and bias voltage V
B
based
on output requirements
Feedback
Circuit
V
(V) Tolerance
Circuit
Load*
Reg.
Line
Reg.
Total
Reg.
Pri./Basic
5.8
±
10%
±
5%
±
1.5%
±
16.5%
Pri./Enhan. 27.8
±
5%
±
2.5%
±
1.5%
±
9%
Opto/Zener 12
±
5%
±
1%
±
0.5%
±
6.5%
Opto/TL431 12
±
1%
±
0.2%
±
0.2%
±
1.4%
*Over 10% to 100% Load Range.
Table 2.
Use primary feedback for lowest cost (for low power
applications only).
Use Opto/Zener for low cost, good output accuracy.
Use Opto/TL431 for best output accuracy.
Set bias voltage V
according to Table 2.
Choose optocoupler from Table 3.
Step-by-Step Design Procedure
This design procedure uses the
PI Expert
design software (available
from Power Integrations), which contains all the important
equations required for a
TOPSwitch-GX
flyback power supply
design, and automates most calculations. Designers are, therefore,
relieved from the tedious calculations involved in the complicated
and highly iterative design process. Look-up tables and empirical
design guidelines are provided in this procedure where appropriate
to facilitate the design task.
Step 1. Determine system requirements: V
ACMAX
, V
ACMIN
,
f
L
, V
O
, P
O
,
η
, Z
Minimum AC input voltage, V
ACMIN
: in volts.
Maximum AC input voltage, V
ACMAX
: in volts.
Recommended AC input ranges:
Input (VAC)
V
ACMIN
(VAC) V
ACMAX
(VAC)
Universal
85
265
230 or 115 with doubler
195
265
Table 1.
Line frequency, f
L
: 50 Hz or 60 Hz.
Output voltage, V
: in Volts.
Output power: P
O
: in Watts.
Figure 3. Primary/Basic Feedback Circuit.
PI-3331-112202
D
S
C
TOPSwitch-GX
L
CONTROL
+
-
F
X
V
AC
C
IN
V
O
15
Feedback Circuit
+
CIRCUIT PERFORMANCE
Circuit Tolerance
±
10%
Load Regulation
±
5%
Line Regulation
±
1.5%
相關PDF資料 |
PDF描述 |
|---|---|
| AN-37 | LinkSwitch-TN Design Guide |
| AN-995A | Electronic Ballasts Using the Cost-Saving IR215X Drivers(153.99 k) |
| AN0416NA | TRANSISTOR | MOSFET | ARRAY | N-CHANNEL | 160V V(BR)DSS | 30MA I(D) | DIP |
| AN0416ND | TRANSISTOR | MOSFET | ARRAY | N-CHANNEL | 160V V(BR)DSS | 25MA I(D) | CHIP |
| AN0416WG | TRANSISTOR | MOSFET | ARRAY | N-CHANNEL | 160V V(BR)DSS | 30MA I(D) | SO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN320 | 功能描述:環境檢測設備 Large Vane CFM/CMM AnemoPsychrometerCO2 RoHS:否 制造商:Fluke 設備類型:Vibration Meter 測量儀器:Vibration |
| AN3200 | 功能描述:大功率LED - 白色 Warm White 100VAC Acrich 4 Watt RoHS:否 制造商:Cree, Inc. 照明顏色:Cool White 顏色溫度:5000 K 光通量:280 lm 顯示角:125 deg 正向電流:700 mA 正向電壓:2.9 V 安裝風格:SMD/SMT 系列:XMLBWW 封裝:Reel |
| AN3200-03 | 制造商:Seoul Semiconductor 功能描述:SSC LED POWER LED |
| AN3200-03-W1-FA | 功能描述:大功率LED - 白色 Warm White 100VAC Acrich 4 Watt RoHS:否 制造商:Cree, Inc. 照明顏色:Cool White 顏色溫度:5000 K 光通量:280 lm 顯示角:125 deg 正向電流:700 mA 正向電壓:2.9 V 安裝風格:SMD/SMT 系列:XMLBWW 封裝:Reel |
| AN3200-03-W1-GA | 功能描述:大功率LED - 白色 Warm White 100VAC Acrich 4 Watt RoHS:否 制造商:Cree, Inc. 照明顏色:Cool White 顏色溫度:5000 K 光通量:280 lm 顯示角:125 deg 正向電流:700 mA 正向電壓:2.9 V 安裝風格:SMD/SMT 系列:XMLBWW 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。