- 您現在的位置：買賣IC網 > PDF目錄364677 > AN-32 TOPSwitch-GX Flyback Design Methodology PDF資料下載
參數資料
| 型號： | AN-32 |
| 英文描述： | TOPSwitch-GX Flyback Design Methodology |
| 中文描述： | 的TOPSwitch - GX系列反激式設計方法 |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 134K |
| 代理商： | AN-32 |
AN-32
15
B
12/02
Customization of secondary designs for each output
The turns for each secondary winding are calculated based on
the respective output voltage V
O
(n):
Output rectifier maximum inverse voltage is
With output RMS current I
(n), secondary number of turns
N
(n) and output rectifier maximum inverse voltage PIV
(n)
known, the secondary side design for each output can now be
carried out exactly the same way as for the single output design.
Secondary winding wire size
The
TOPSwitch-GX
design spreadsheet assumes a CMA of 200
when calculating secondary winding wire diameters. This gives
the minimum wire sizes required for the RMS currents of each
output using seperate windings. Designers may wish to use
larger size wire for better thermal performance. Other
considerations such as skin effect and bobbin coverage may
suggest the use of a smaller wire by using multiple strands
wound in parallel. In addition, practical considerations in
transformer manufacturing may also dictate the wire size.
I
n
I n
I
I
SRMS
SRMS
O
( )
=
×
Appendix A
Multiple Output Flyback Power
Supply Design
The only difference between a multiple output flyback power
supply and a single output flyback power supply of the same
total output power is in the secondary side design. Instead of
delivering all power to one output as in the single output case,
a multiple output flyback distributes its output power among
several outputs. Therefore, the design procedure for the primary
side stays the same, while that for the secondary side demands
further considerations.
Design with lumped output power
One simple way of doing multiple output flyback design is
described in detail in AN-22, “Designing Multiple Output
Flyback Power Supplies with
TOPSwitch
”. The design method
starts with a single output equivalent by lumping output power
of all outputs to one main output. Secondary peak current I
and
RMS current I
are derived. Output average current I
O
corresponding to the lumped power is also calculated.
Assumption for simplification
The current waveforms in the individual output windings are
determined by the impedance in each circuit, which is a function
of leakage inductance, rectifier characteristics, capacitor value
and most importantly, output load. Although this current
waveform may not be exactly the same from output to output,
it is reasonable to assume that, to the first order, all output
currents have the same shape as for the single output equivalent
of lumped power.
Output RMS current vs. average current
The output average current is always equal to the DC load
current, while the RMS value is determined by current wave
shape. Since the current wave shapes are assumed to be the
same for all outputs, their ratio of RMS to average currents must
also be identical. Therefore, with the output average current
known, the RMS current for each output winding can be
calculated as
where I
(n) and I
(n) are the secondary RMS current and
output average current of the n
th
output and I
and I
are the
secondary RMS current and output average current for the
lumped single output equivalent design.
N n
N
V n
V n
V
D
V
S
=
×
+
+
PIV n
V
N n
N
V n
MAX
P
=
×
+
相關PDF資料 |
PDF描述 |
|---|---|
| AN-37 | LinkSwitch-TN Design Guide |
| AN-995A | Electronic Ballasts Using the Cost-Saving IR215X Drivers(153.99 k) |
| AN0416NA | TRANSISTOR | MOSFET | ARRAY | N-CHANNEL | 160V V(BR)DSS | 30MA I(D) | DIP |
| AN0416ND | TRANSISTOR | MOSFET | ARRAY | N-CHANNEL | 160V V(BR)DSS | 25MA I(D) | CHIP |
| AN0416WG | TRANSISTOR | MOSFET | ARRAY | N-CHANNEL | 160V V(BR)DSS | 30MA I(D) | SO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN320 | 功能描述:環境檢測設備 Large Vane CFM/CMM AnemoPsychrometerCO2 RoHS:否 制造商:Fluke 設備類型:Vibration Meter 測量儀器:Vibration |
| AN3200 | 功能描述:大功率LED - 白色 Warm White 100VAC Acrich 4 Watt RoHS:否 制造商:Cree, Inc. 照明顏色:Cool White 顏色溫度:5000 K 光通量:280 lm 顯示角:125 deg 正向電流:700 mA 正向電壓:2.9 V 安裝風格:SMD/SMT 系列:XMLBWW 封裝:Reel |
| AN3200-03 | 制造商:Seoul Semiconductor 功能描述:SSC LED POWER LED |
| AN3200-03-W1-FA | 功能描述:大功率LED - 白色 Warm White 100VAC Acrich 4 Watt RoHS:否 制造商:Cree, Inc. 照明顏色:Cool White 顏色溫度:5000 K 光通量:280 lm 顯示角:125 deg 正向電流:700 mA 正向電壓:2.9 V 安裝風格:SMD/SMT 系列:XMLBWW 封裝:Reel |
| AN3200-03-W1-GA | 功能描述:大功率LED - 白色 Warm White 100VAC Acrich 4 Watt RoHS:否 制造商:Cree, Inc. 照明顏色:Cool White 顏色溫度:5000 K 光通量:280 lm 顯示角:125 deg 正向電流:700 mA 正向電壓:2.9 V 安裝風格:SMD/SMT 系列:XMLBWW 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。