- 您現在的位置：買賣IC網 > PDF目錄364674 > AMIS-720233-B Contact Image Sensor PDF資料下載
參數資料
| 型號： | AMIS-720233-B |
| 英文描述： | Contact Image Sensor |
| 中文描述： | 接觸式圖像傳感器 |
| 文件頁數： | 4/12頁 |
| 文件大小： | 403K |
| 代理商： | AMIS-720233-B |
AMIS-720233-B:
Contact Image Sensor
Data Sheet
4.0 Electro-Optical Characteristics (25
°
C)
The electro-optical characteristics of AMIS-720233-B imaging sensor chip are listed in Table 2. These values are measured at 25
°
C.
Table 2: Electro-Optical Characteristics
Parameters
Symbols
Typical
Number of photo-elements
64
Pixel-to-pixel spacing
125
Line scanning rate
Tint
(1)
864
Clock frequency
Fclk
(2)
2.0
Units
Elements
μ
m
μ
s/line
MHz
Notes
See Note 2 for higher clock speed.
(maximum 5MHz)
Exp = 1.8 X 10
μJ/cm
2
Notes 5 & 3
Notes 6 & 3
Output voltage
Output voltage non-uniformity
Dark output voltage
Dark output non-uniformity
Adjacent pixel non-uniformity
Chip-to-chip non-uniformity
Notes:
1.
Tint stands for the line scanning rate or the integration time. It is determined by the time interval between two SPs.
2.
Fclk stands for the input clock frequency. For Fclk > 2.0MHz see Note 3 and the Section 5.
3.
Vpavg =
∑
Vp(n)/Npixels (average level in one line scan).
Where Vp(n) is the amplitude of n
pixel in the sensor chip and Npixels is the total number of pixels in sensor chip. Vpavg is converted from impulse current video
pixel into a voltage output (see Figure 4 and
4.
Figure
5
).
Exp = LP x Tint, where LP is light power (Yellow-Green) and tint is as defined above (see Figure 6).
5.
Up is the uniformity specification, measured under a uniform exposing light exposure. Up = [Vp(max) - Vpavg] / Vpavg x 100% or [Vpavg - Vp(min)] / Vpavg} x
100%, whichever is greater.
Where Vp(max) is the maximum pixel output voltage in the light.
Vp(min) is the minimum pixel output voltage in the light.
6.
Vd =
∑
Vp(n)/Npixels. Where Vp(n) is the pixels signal amplitude of the n
th
pixel of the sensor. Dark is where the sensor is placed in the dark environment.
7.
Ud = Vdmax – Vdmin. Dark is same definition as above.
8.
Upadj = MAX[ | (Vp(n) - Vp(n+l) | / Vp(n)) x 100%. Upadj is the non-uniformity in percentage. It is the amplitude difference between two neighboring pixels.
9.
Ucc is the uniformity specifications, measured among the good die on the wafer. Under uniform light exposure the sensors are measured and calculated with
following algorithm: Vpavg of all the good dies on the wafer are averaged and assigned VGpavg. Then the die with maximum Vpavg is assigned Vpavg(max),
and the one with minimum Vpavg is assigned Vpavg(min). Then UCC = {[Vpavg(max)-Vpavg(min)]/VGpavg}x100.
Vpavg
(3)
Up
(4)
Vd
(5)
Ud
(6)
Upadj
(7)
Ucc
(8)
1.0
±
7.5
<20
<10
<7.5
±
7.5
V
%
mV
mV
%
%
4
AMI Semiconductor
–May 06, M-20567-001
www.amis.com
相關PDF資料 |
PDF描述 |
|---|---|
| AMIS-720341 | Contact Image Sensor |
| AMIS-720341-A | Contact Image Sensor |
| AMIS-720442 | 400dpi Contact Image Sensor |
| AMIS-720442-A | 400dpi Contact Image Sensor |
| AMIS-720639 | 600dpi CIS Sensor Chip |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS-720341 | 制造商:AMI 制造商全稱:AMI 功能描述:Contact Image Sensor |
| AMIS-720341-A | 制造商:AMI 制造商全稱:AMI 功能描述:Contact Image Sensor |
| AMIS-720442 | 制造商:AMI 制造商全稱:AMI 功能描述:400dpi Contact Image Sensor |
| AMIS-720442-A | 制造商:AMI 制造商全稱:AMI 功能描述:400dpi Contact Image Sensor |
| AMIS-720639 | 制造商:AMI 制造商全稱:AMI 功能描述:600dpi CIS Sensor Chip |
發布緊急采購，3分鐘左右您將得到回復。