- 您現在的位置：買賣IC網 > PDF目錄364674 > AMIS-720233-B Contact Image Sensor PDF資料下載
參數資料
| 型號： | AMIS-720233-B |
| 英文描述： | Contact Image Sensor |
| 中文描述： | 接觸式圖像傳感器 |
| 文件頁數： | 10/12頁 |
| 文件大小： | 403K |
| 代理商： | AMIS-720233-B |
AMIS-720233-B:
Contact Image Sensor
Data Sheet
Table 5: Timing Symbol's Definition
Item
Clock cycle time
Clock pulse width
(1)
Clock duty cycle
Data setup time
Data hold time
Prohibit crossing time
(2)
EOS rise delay
EOS fall delay
Signal delay time
(3)
Signal settling time
(3)
Notes:
1.
Since the clock pulse width varies with the frequency, tw will vary according to duty cycle.
2.
Prohibit crossing time is to insure that no two SPs are locked into the shift register for any single scan time. Since the SP is entered into the shift register during its
active high level when the CP clock edges falls, the active high of the SP is permitted only during one falling, CP clock edges for any given scan. Otherwise,
multiple SPs will load into the shift register.
3.
Pixel delay times and settling time depend on the output amplifier, which is employed. These values, tdl and ts/h, are measured with the amplifier see in Figure 9
using the AMIS-720233-B sensors. Note: The impulse signal current out of the device has pulse width ~ 30ns. Hence, the faster the amplifier with a faster settling
time will yield a signal video pulse with faster rise and settle times.
Symbol
to
tw
tds
tdh
tprh
terdl
tefdl
tdl
ts/h
Min.
200
50
25
20
20
Mean
50
20
60
70
20
120
Max.
10000
75
Units
ns
ns
%
ns
ns
ns
ns
ns
ns
ns
9.0 Typical A6 CIS Module Circuit
Figure 9 depicts a typical A6 CIS module circuit using the AMIS-720233-B sensors. The circuit is provided as a reference to illustrate
the interconnection of the AMIS-720233-B with a serially cascaded line of image sensors. It is a typical A6 size CIS module produced
by AMIS. It provides the first-time user with additional insight for designing a CIS module and supplements the circuit descriptions
given in Section 5.
The difference is in the arrangement of the two shunt switches - U2D and U2A. U2D is a counterpart to SW in
Figure 5. A DC restoration capacitor, C20, with value of 100pf is added between the shunt’s switch. The first, U2D, clamps the video
line to ground to reset the image sensors. Simultaneously the second, U2A, clamps the node between C20 and amplifier input to an
output reference bias voltage that is on the node between R4 and R9. These resistors are voltage dividers that set the DC operating
level of the amplifier’s output by applying same bias voltage to both inputs of the amplifier. See Figure 9.
10
AMI Semiconductor
–May 06, M-20567-001
www.amis.com
相關PDF資料 |
PDF描述 |
|---|---|
| AMIS-720341 | Contact Image Sensor |
| AMIS-720341-A | Contact Image Sensor |
| AMIS-720442 | 400dpi Contact Image Sensor |
| AMIS-720442-A | 400dpi Contact Image Sensor |
| AMIS-720639 | 600dpi CIS Sensor Chip |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS-720341 | 制造商:AMI 制造商全稱:AMI 功能描述:Contact Image Sensor |
| AMIS-720341-A | 制造商:AMI 制造商全稱:AMI 功能描述:Contact Image Sensor |
| AMIS-720442 | 制造商:AMI 制造商全稱:AMI 功能描述:400dpi Contact Image Sensor |
| AMIS-720442-A | 制造商:AMI 制造商全稱:AMI 功能描述:400dpi Contact Image Sensor |
| AMIS-720639 | 制造商:AMI 制造商全稱:AMI 功能描述:600dpi CIS Sensor Chip |
發布緊急采購，3分鐘左右您將得到回復。