- 您現在的位置：買賣IC網 > PDF目錄364674 > AMIS-710651-A4 Color CIS Module PDF資料下載
參數資料
| 型號： | AMIS-710651-A4 |
| 英文描述： | Color CIS Module |
| 中文描述： | 彩色CIS模塊 |
| 文件頁數： | 3/9頁 |
| 文件大?。?/td> | 197K |
| 代理商： | AMIS-710651-A4 |
AMIS-710651-A4: Color CIS Module
Data Sheet
7.0 Electro-Optical Characteristics (25
°
C)
All tests were conducted at the typical pixel rate of 3.0MHz
Table 4: Electro-Optical Characteristics (25°C)
Parameter
Number of active photo detectors
Symbol
Typ.
5160
2580
42.3
84.6
~1.75
3.0
3.0
0.2
< /-30
<60
<25
<150
Units
Elements
Note
600dpi
300dpi
600dpi
300dpi
Pixel-to-pixel spacing
μ
m
Line scan rate
Clock frequency
Pixel rate
Bright output voltage
Bright output non-uniformity
Bright output total non-uniformity
Adjacent pixel non-uniformity
Dark non-uniformity
Dark output voltage range
Random noise
TINT
(1)
FREQ
(2)
PRATE
(2)
Vpavg
(3)
+/- Up
(4)
Uptotal
(5)
Uadj
(6)
Ud
(7)
VDL
(8)
RNL
(9)
ms/line
MHz
MHz
V
%
%
%
mV
V
p-p mV
rms mV
%
@ 3.0MHz clock frequency
1.2<VDL<1.5
<24
<4
40
Modulation transfer function
Notes:
(1)
Scan rate (integration time), TINT, is determined by the time interval between two SPs. See Table 3, Note 5.
(2)
Clock frequency, FREQ, is the input clock frequency and its corresponding PRATE is the pixel sample rate.
(3)
Bright output voltage Vpmax = maximum pixel value of Vp(n), Vpmin = minimum pixel value of Vp(n), Vpavg =
∑
Vp(n)/5160; where Vp(n) is the n
th
pixel in a line
scan with the module scanning a uniform white target and Vp values are measured with a uniform exposure.
(4)
Bright output non-uniformity Up(+) = [(Vpmax - Vpavg) / Vpavg] x 100%, Up(-)= [(Vpavg - Vpmin) / Vpavg] x 100%, whichever polarity with the highest absolute
value is selected.
(5)
Bright output total non-uniformity: Uptotal = [Vpmax -Vpmin]/Vpavg x 100%
(6)
Adjacent pixel non-uniformity: Upadj = MAX[ | (Vp(n) - Vp(n+l) | / Vp(n))] x 100%
Upadj is the non-uniformity in percentage. It is the maximum difference amplitude between two neighboring pixels.
(7)
Dark non-uniformity: Ud = Vdmax – Vdmin
Vdmax is the max. pixel value of the video pixel in the dark. Vdmin is the min. pixel value of the video pixel in the dark. The references for these levels are the dark
level (VDL).
(8)
Dark output voltage range (VDL) is the level between the output dark level and ground.
(9)
Random noise (RNL): The rms value was calculated from measured p-p thermal noise taken at output from a selected pixel. The rms is defined as one standard
deviation of at least 64 pixels sampled. The calculation of the standard deviation is based on an idealized Gaussian probability curve.
(10) Modulation transfer function is defined as MTF = [(Vmax - Vmin) / (Vmax + Vmin)] x 100%. MTF is a measure at the glass surface. Vmax is the maximum output
voltage at 300lp/inch (at 1/2 of the optical Nyquest frequency) and Vmin is the minimum output voltage at 300lp/inch.
MTF
(10)
8.0 Electrical Clocking Characteristics
Table 5: Clock Amplitude Duty Characteristics (25
°
C)
Parameter
Clock input voltage
Symbol
VIH
VIL
(1)
FREQ
(2)
PRATE
(2)
TINT
(4)
Ratio = twp / tp
(5)
Min.
Typ.
Max.
Units
See Table 3
Clock frequency
Pixel rate
Line read time
Clock pulse duty cycle
Notes:
(1)
The clocks, CP and SP are compatible with CMOS clock drivers.
(2)
FREQ is the clock frequency and PRATE is the pixel sample rate.
(3)
Minimum values are not specified because it will be determined by the maximum TINT value. See Note 4.
(4)
TINT is the line scan read time, which depends on the interval between the SP entries. The minimum time is determined by (1/clock frequency) x (5160 +
150) pixels. Note that there are a few extra pixels used to determine the typical line time of 820μsec @ 3.0MHz PRATE (see Figure 1). There are 55 clocks
required to transfer and reset the photo-sites before the video can be scanned out. The longest integration time is determined by the degree of leakage
current degradation that can be tolerated by the system. A 10ms maximum is a typical rule-of-thumb. An experienced CIS user can use his discretion and
determine the desired tolerance level for the given system.
(5)
The definition for the symbols used in the ratio is defined in
Figure 1
. A duty cycle of exactly 50 percent is recommended to maintain equal pixel duration
between odd and even pixels.
Note 3
~1.30
45
3.0
3.0
4.0
4.0
~10
MHz
MHz
ms
%
3
AMI Semiconductor
– Aug. 06, M-20609-001
www.amis.com
相關PDF資料 |
PDF描述 |
|---|---|
| AMIS-720233 | Contact Image Sensor |
| AMIS-720233-B | Contact Image Sensor |
| AMIS-720341 | Contact Image Sensor |
| AMIS-720341-A | Contact Image Sensor |
| AMIS-720442 | 400dpi Contact Image Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS-720233 | 制造商:AMI 制造商全稱:AMI 功能描述:Contact Image Sensor |
| AMIS-720233-B | 制造商:AMI 制造商全稱:AMI 功能描述:Contact Image Sensor |
| AMIS-720341 | 制造商:AMI 制造商全稱:AMI 功能描述:Contact Image Sensor |
| AMIS-720341-A | 制造商:AMI 制造商全稱:AMI 功能描述:Contact Image Sensor |
| AMIS-720442 | 制造商:AMI 制造商全稱:AMI 功能描述:400dpi Contact Image Sensor |
發布緊急采購，3分鐘左右您將得到回復。