- 您現在的位置：買賣IC網 > PDF目錄364674 > AMC6821SDBQ Analog Monitor and Control Circuit PDF資料下載
參數資料
| 型號： | AMC6821SDBQ |
| 英文描述： | Analog Monitor and Control Circuit |
| 中文描述： | 模擬監視和控制電路 |
| 文件頁數： | 33/47頁 |
| 文件大小： | 547K |
| 代理商： | AMC6821SDBQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
www.ti.com
P
AMC6821
SBAS386A–MAY 2006–REVISED MAY 2006
Configuration Register 4 (Address 0x04, Value After Power-On Reset = 0x08)
BIT
NAME
R/W
DEFAULT
DESCRIPTION
TODIS = 0, SMBus timeout enabled (default); TODIS = 1, SMBus timeout disabled. The
AMC6821 includes an SMBus timeout feature. Timeout is enabled (TODIS = 0) if a
single clock is held low longer than 30ms (
±
10%). When this timeout occurs, the
AMC6821 releases the bus (stops driving the bus and lets SCLK and SDA float high),
resets the communication, and is able to receive new START conditions. When TODIS
= 1, timeout is disabled. In this case, when the clock resumes after being held low for
longer than 30ms, the AMC6821 continues the bus communication at the current point.
Number of pulses per revolution of the fan. Power-on default = 0. PLSPR = 0 for two
pulses/revolution (default), PLSPR = 1 for four pulses per revolution.
When TACH-FAST = 1, the TACH data reading is updated every 250ms. This monitor is
the fast RPM monitor. When TACH-FAST = 0, the TACH data reading is updated every
second. Default = 0, power-on default = 0.
Setting this bit to '1' enables the OVR pin. Clearing this bit ('0') disables the OVR pin
(high-impedance). Default = 0.
Read back '1'. Reading this bit returns 1, not 0.
Read-back '0'.
Read-back '0'.
Read-back '0'.
7
TODIS
R/W
0
6
PSPR
R/W
0
5
TACH-FAST
R/W
0
4
OVREN
R/W
0
3
2
1
0
Reserved
Reserved
Reserved
Reserved
R
R
R
R
1
0
0
0
Writing the reserved bit has no effect.
33
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| AMC6821SDBQR | Analog Monitor and Control Circuit |
| AMD-8111 | AMD-8111? HyperTransport? I/O Hub Revision Guide |
| AMD-8131 | AMD-8131 - AMD-8131 HyperTransport PCI-X Tunnel Data Sheet |
| AMD-8151 | AMD-8151 - Preliminary AMD-8151 HyperTransport AGP3.0 Graphics Tunnel Data Sheet |
| AMD64 | AMD64 Architecture Programmer＇s Manual Volume 1: Application Programming |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMC6821SDBQG4 | 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMC6821SDBQR | 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMC6821SDBQRG4 | 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Control RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMC6821SQDBQRQ1 | 功能描述:馬達/運動/點火控制器和驅動器 Auto Cat Temp Mon and Fan Control RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMC682J50ACK | 制造商:Nissei Electric 功能描述:CAPACITOR, METALLIZED FILM, POLYESTER, 50 V, 0.0068 uF, THROUGH HOLE MOUNT |
發布緊急采購，3分鐘左右您將得到回復。