參數資料
型號： AMC6821SDBQ
英文描述： Analog Monitor and Control Circuit
中文描述： 模擬監視和控制電路
文件頁數： 14/47頁
文件大?。?/td> 547K
代理商： AMC6821SDBQ
www.ti.com
P
FAN SPEED MEASUREMENT
The AMC6821 monitors the fan speed (RPM) via the TACH pin (
Figure 8
illustrates this process). The TACH-EN
bit of
Configuration Register 2
(bit 2, 0x01) enables the fan speed measurement. When TACH-EN is cleared
('0'), the measurement is disabled. The measurement is enabled when the TACH-EN bit is set to '1'. This section
describes the device behavior when TACH-EN is set ('1').
AMC6821
SBAS386A–MAY 2006–REVISED MAY 2006
Table 5. PWM Frequency
PWM2
PWM1
PWM0
PWM FREQUENCY
When the PWM-MODE Pin is Floating or Tied to V
DD
0
1
0
1
0
1
0
1
When the PWM-MODE Pin is Tied to GND
0
1
0
1
0
1
0
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
10Hz
15Hz
23Hz
30Hz (default)
38Hz
47Hz
62Hz
94Hz
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
1kHz
10kHz
20kHz
25kHz (default)
30kHz
40kHz
40kHz
40kHz
The on-chip fan-speed counter does not count the fan tach output pulses directly because of the low RPM of the
fan. Instead, the period of the fan revolution is measured by gating an on-chip clock (100kHz). The result is
stored in the
TACH-DATA Register
that contains two bytes (16 bits total). RPM monitoring is disabled when the
START bit of
Configuration Register 1
or the TACH-EN bit of
Configuration Register 2
is cleared ('0'), and is
enabled when START = 1 and TACH-EN = 1.
If the TACH-MODE bit is cleared, RPM monitoring stops and the TACH-DATA register is not updated when the
duty cycle is less than 7%. If the TACH mode is equal to '1' the RPM monitoring is always performed, and the
TACH data are always updated after each monitoring.
14
Submit Documentation Feedback
相關PDF資料
PDF描述
AMC6821SDBQR Analog Monitor and Control Circuit
AMD-8111 AMD-8111? HyperTransport? I/O Hub Revision Guide
AMD-8131 AMD-8131 - AMD-8131 HyperTransport PCI-X Tunnel Data Sheet
AMD-8151 AMD-8151 - Preliminary AMD-8151 HyperTransport AGP3.0 Graphics Tunnel Data Sheet
AMD64 AMD64 Architecture Programmer＇s Manual Volume 1: Application Programming
相關代理商/技術參數
參數描述
AMC6821SDBQG4 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMC6821SDBQR 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMC6821SDBQRG4 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Control RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMC6821SQDBQRQ1 功能描述:馬達/運動/點火控制器和驅動器 Auto Cat Temp Mon and Fan Control RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMC682J50ACK 制造商:Nissei Electric 功能描述:CAPACITOR, METALLIZED FILM, POLYESTER, 50 V, 0.0068 uF, THROUGH HOLE MOUNT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*