參數資料
型號： AMC6821SDBQ
英文描述： Analog Monitor and Control Circuit
中文描述： 模擬監視和控制電路
文件頁數： 17/47頁
文件大小： 547K
代理商： AMC6821SDBQ
www.ti.com
P
FAN FAILURE DETECTION
When the TACH data are larger than the TACH low limit, the fan runs at a speed below the predefined minimum
RPM. When this condition occurs, a spin-up process is applied to start the fan again when spin-up is enabled.
Bits [STIME2:STIME0] of the
Fan Characteristics Register
define this time period.
Figure 10
shows the function
of the fan failure detection.
During Spin-Up Process
Normal Operation of Fan Failure
Detection and Spin-Up
Bit FANS = 0
Clear Spin-Up
Time Counter
TACH Data > Low Limit
Measure RPM
Yes
Yes
No
No
No
No
Yes
Yes
No Spin-Up if Disabled
Bit FANS = 1
Spin-Up Time Count +1
Spin-Up Process
Spin-Up Time Count
5
3
Fan failure,
FAN-FAULT
pin
goes low.
Spin-Up Disabled
Measure the RPM continuously once every 0.25s (TACH-FAST
even after a fan failure. However, there are no FANS detections during spin-up.
The
pin is negated if the fan returns to a normal RPM range.
FAN-FAULT
= 1) or 1s
bit
(TACH-FAST = 0),
AMC6821
SBAS386A–MAY 2006–REVISED MAY 2006
The fan speed is measured immediately after spin-up and the TACH-FAST bit of
Configuration Register 4
determines the monitoring rate. If the fan does not return to a normal range after five consecutive spin-ups, a
FAN-FAILURE occurs, the FAN-FAULT pin goes low when it is enabled (the FAN-FAULT-EN bit of
Configuration
Register 1
is set), and the spin-up process continues. If the fan returns to a normal speed range before the fifth
spin-up, the FAN-FAULT pin does not go low even though the FANS bit is still set to '1'. No FANS (fan-slow)
detections are performed during spin-up.
Figure 10. Fan Failure Detection and Spin-Up
17
Submit Documentation Feedback
相關PDF資料
PDF描述
AMC6821SDBQR Analog Monitor and Control Circuit
AMD-8111 AMD-8111? HyperTransport? I/O Hub Revision Guide
AMD-8131 AMD-8131 - AMD-8131 HyperTransport PCI-X Tunnel Data Sheet
AMD-8151 AMD-8151 - Preliminary AMD-8151 HyperTransport AGP3.0 Graphics Tunnel Data Sheet
AMD64 AMD64 Architecture Programmer＇s Manual Volume 1: Application Programming
相關代理商/技術參數
參數描述
AMC6821SDBQG4 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMC6821SDBQR 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMC6821SDBQRG4 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Control RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMC6821SQDBQRQ1 功能描述:馬達/運動/點火控制器和驅動器 Auto Cat Temp Mon and Fan Control RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMC682J50ACK 制造商:Nissei Electric 功能描述:CAPACITOR, METALLIZED FILM, POLYESTER, 50 V, 0.0068 uF, THROUGH HOLE MOUNT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*