參數資料
型號： AM29F080B-70SI
英文描述： x8 Flash EEPROM
中文描述： x8閃存EEPROM的
文件頁數： 19/39頁
文件大?。?/td> 728K
代理商： AM29F080B-70SI
Am29F002B/Am29F002NB
19
The DQ5 failure condition may appear if the system
tries to program a “1” to a location that is previously pro-
grammed to “0.”
Only an erase operation can change
a “0” back to a “1.”
Under this condition, the device
halts the operation, and when the operation has
exceeded the timing limits, DQ5 produces a “1.”
Under both these conditions, the system must issue the
reset command to return the device to reading array
data.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If addi-
tional sectors are selected for erasure, the entire time-
out also applies after each additional sector erase com-
mand. When the time-out is complete, DQ3 switches
from “0” to “1.” The system may ignore DQ3 if the
system can guarantee that the time between additional
sector erase commands will always be less than 50
μ
s.
See also the “Sector Erase Command Sequence”
section.
After the sector erase command sequence is written,
the system should read the status on DQ7 (Data#
Polling) or DQ6 (Toggle Bit I) to ensure the device has
accepted the command sequence, and then read DQ3.
If DQ3 is “1”, the internally controlled erase cycle has
begun; all further commands (other than Erase Sus-
pend) are ignored until the erase operation is complete.
If DQ3 is “0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status
of DQ3 prior to and following each subsequent sector
erase command. If DQ3 is high on the second status
check, the last command might not have been
accepted. Table 6 shows the outputs for DQ3.
START
No
Yes
Yes
DQ5 = 1
No
Yes
Toggle Bit
= Toggle
No
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Read DQ7–DQ0
Toggle Bit
= Toggle
Read DQ7–DQ0
Twice
Read DQ7–DQ0
Notes:
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as DQ5
changes to “1”. See text.
Figure 5.
Toggle Bit Algorithm
(Notes
1, 2)
(Note 1)
相關PDF資料
PDF描述
AM29F080B-90EE 75V Single N-Channel HEXFET Power MOSFET in a TO-220AB package; Similar to IRFB3507 with Lead Free Packaging
AM29F080B-90FE 55V Single N-Channel HEXFET Power MOSFET in a I-Pak package; Similar to IRLU2905Z with Lead Free Packaging
AM29F080B-90SE 200V Single N-Channel HEXFET Power MOSFET in a SO-8 package; Similar to IRF7464 with Lead Free Packaging
AM29F100AB-150FC 55V Single N-Channel HEXFET Power MOSFET in a TO-220 FullPak (Iso) package; A IRFIZ34N with Standard Packaging
AM29F100AB-150FE x8/x16 Flash EEPROM
相關代理商/技術參數
參數描述
AM29F080B-75EF 制造商:Spansion 功能描述:8 MEGABIT 1 M X 8-BIT CMOS 5.0 VOLT-ONLY, UNIFORM SECTOR FLASH MEMORY
AM29F080B-75EI 制造商:Spansion 功能描述:IC,EEPROM,NOR FLASH,1MX8,CMOS,TSSOP,40PIN,PLASTIC
AM29F080B-90EC 制造商:Advanced Micro Devices 功能描述: 制造商:Spansion 功能描述:IC, FLASH MEM, 8MBIT, 90NS, 40-TSOP, Memory Type:Flash - NOR, Memory Size:8Mbit,
AM29F080B-90ED 制造商:Spansion 功能描述:IC FLASH 8MB SMD 29F080 TSOP40
AM29F080B90EF 制造商:Advanced Micro Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*