參數資料
型號： AGLN250V5-ZVQG100I
廠商： Microsemi SoC
文件頁數： 8/150頁
文件大小： 0K
描述： IC FPGA NANO 1KB 250K 100VQFP
標準包裝： 90
系列： IGLOO nano
邏輯元件/單元數： 6144
RAM 位總計： 36864
輸入/輸出數： 68
門數： 250000
電源電壓： 1.425 V ~ 1.575 V
安裝類型： 表面貼裝
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-TQFP
供應商設備封裝： 100-VQFP（14x14）
Revision 17
3-1
3 – Pin Descriptions
Supply Pins
GND
Ground
Ground supply voltage to the core, I/O outputs, and I/O logic.
GNDQ
Ground (quiet)
Quiet ground supply voltage to input buffers of I/O banks. Within the package, the GNDQ plane is
decoupled from the simultaneous switching noise originated from the output buffer ground domain. This
minimizes the noise transfer within the package and improves input signal integrity. GNDQ must always
be connected to GND on the board.
VCC
Core Supply Voltage
Supply voltage to the FPGA core, nominally 1.5 V for IGLOO nano V5 devices, and 1.2 V or 1.5 V for
IGLOO nano V2 devices. VCC is required for powering the JTAG state machine in addition to VJTAG.
Even when a device is in bypass mode in a JTAG chain of interconnected devices, both VCC and VJTAG
must remain powered to allow JTAG signals to pass through the device.
VCCIBx
I/O Supply Voltage
Supply voltage to the bank's I/O output buffers and I/O logic. Bx is the I/O bank number. There are up to
eight I/O banks on low power flash devices plus a dedicated VJTAG bank. Each bank can have a
separate VCCI connection. All I/Os in a bank will run off the same VCCIBx supply. VCCI can be 1.2 V,
1.5 V, 1.8 V, 2.5 V, or 3.3 V, nominal voltage. Unused I/O banks should have their corresponding VCCI
pins tied to GND.
VMVx
I/O Supply Voltage (quiet)
Quiet supply voltage to the input buffers of each I/O bank. x is the bank number. Within the package, the
VMV plane biases the input stage of the I/Os in the I/O banks. This minimizes the noise transfer within
the package and improves input signal integrity. Each bank must have at least one VMV connection, and
no VMV should be left unconnected. All I/Os in a bank run off the same VMVx supply. VMV is used to
provide a quiet supply voltage to the input buffers of each I/O bank. VMVx can be 1.2 V, 1.5 V, 1.8 V,
2.5 V, or 3.3 V, nominal voltage. Unused I/O banks should have their corresponding VMV pins tied to GND.
VMV and VCCI should be at the same voltage within a given I/O bank. Used VMV pins must be
connected to the corresponding VCCI pins of the same bank (i.e., VMV0 to VCCIB0, VMV1 to VCCIB1,
etc.).
VCCPLA/B/C/D/E/F
PLL Supply Voltage
Supply voltage to analog PLL, nominally 1.5 V or 1.2 V.
When the PLLs are not used, the Microsemi Designer place-and-route tool automatically disables the
unused PLLs to lower power consumption. The user should tie unused VCCPLx and VCOMPLx pins to
ground. Microsemi recommends tying VCCPLx to VCC and using proper filtering circuits to decouple
VCC noise from the PLLs. Refer to the PLL Power Supply Decoupling section of the "Clock Conditioning
Circuits in IGLOO and ProASIC3 Devices" chapter in the IGLOO nano FPGA Fabric User’s Guide for a
complete board solution for the PLL analog power supply and ground.
There is one VCCPLF pin on IGLOO nano devices.
VCOMPLA/B/C/D/E/F
PLL Ground
Ground to analog PLL power supplies. When the PLLs are not used, the Microsemi Designer place-and-
route tool automatically disables the unused PLLs to lower power consumption. The user should tie
unused VCCPLx and VCOMPLx pins to ground.
There is one VCOMPLF pin on IGLOO nano devices.
VJTAG
JTAG Supply Voltage
Low power flash devices have a separate bank for the dedicated JTAG pins. The JTAG pins can be run
at any voltage from 1.5 V to 3.3 V (nominal). Isolating the JTAG power supply in a separate I/O bank
gives greater flexibility in supply selection and simplifies power supply and PCB design. If the JTAG
相關PDF資料
PDF描述
AGL250V2-CS196 IC FPGA 1KB FLASH 250K 196-CSP
BR24S64FJ-WE2 IC EEPROM 64KBIT 400KHZ 8SOP
RSM36DTAN CONN EDGECARD 72POS R/A .156 SLD
RSM36DTAH CONN EDGECARD 72POS R/A .156 SLD
BR25L160FJ-WE2 IC EEPROM 16KBIT 5MHZ 8SOP
相關代理商/技術參數
參數描述
AGLN-NANO-KIT 功能描述:KIT HARDWARE FOR AGLN-NANO RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:IGLOO nano 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
AGLP030V2-CS201 功能描述:IC FPGA IGLOO PLUS 30K 201-CSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO PLUS 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14）
AGLP030V2-CS201I 功能描述:IC FPGA IGLOO PLUS 30K 201-CSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO PLUS 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14）
AGLP030-V2CS289 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO PLUS Low-Power Flash FPGAs with FlashFreeze Technology
AGLP030V2-CS289 功能描述:IC FPGA IGLOO PLUS 30K 289-CSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO PLUS 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14）
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*