參數資料
型號： ADZS-BF537-EZLITE
廠商： Analog Devices Inc
文件頁數： 8/68頁
文件大?。?/td> 0K
描述： BOARD EVAL ADSP-BF537
產品培訓模塊： Interfacing AV Converters to Blackfin Processors
Blackfin® Processor Core Architecture Overview
Blackfin® Device Drivers
Blackfin® Optimizations for Performance and Power Consumption
Blackfin® System Services
Introduction to VisualDSP++® Tools
特色產品： Blackfin? BF50x Series Processors
標準包裝： 1
系列： Blackfin®
類型： DSP
適用于相關產品： ADSP-BF537
所含物品： 評估板、軟件和說明文檔
配用： ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARD
ADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE
ADZS-USBLAN-EZEXT-ND - BOARD DAUGHTER EXTENDED USB-LAN
ADZS-BFFPGA-EZEXT-ND - BOARD EVAL FPGA BLACKFIN EXTENDR
相關產品： ADSP-BF537KBCZ-6BV-ND - IC DSP CTLR 16BIT 208CSPBGA
ADSP-BF537BBCZ-5BV-ND - IC DSP CTLR 16BIT 208CSPBGA
ADSP-BF537KBCZ-6AV-ND - IC DSP CTLR 16BIT 182CSPBGA
ADSP-BF537BBCZ-5AV-ND - IC DSP CTLR 16BIT 182CSPBGA
ADSP-BF537BBCZ-5B-ND - IC DSP CTLR 16BIT 208CSPBGA
ADSP-BF537BBC-5A-ND - IC DSP CTLR 16BIT 182CSPBGA
Rev. J
|
Page 16 of 68
|
February 2014
(VCO) and the system clock. SCLK divider values are 1 through
15. Table 6 illustrates typical system clock ratios.
Note that the divisor ratio must be chosen to limit the system
clock frequency to its maximum of fSCLK. The SSEL value can be
changed dynamically without any PLL lock latencies by writing
the appropriate values to the PLL divisor register (PLL_DIV).
The core clock (CCLK) frequency can also be dynamically
changed by means of the CSEL1–0 bits of the PLL_DIV register.
Supported CCLK divider ratios are 1, 2, 4, and 8, as shown in
Table 7. This programmable core clock capability is useful for
fast core frequency modifications.
The maximum CCLK frequency not only depends on the part’s
speed grade (see Ordering Guide on Page 67), it also depends on
the applied VDDINT voltage (see Table 10, Table 11, and Table 12
on Page 24 for details). The maximal system clock rate (SCLK)
depends on the chip package and the applied VDDEXT voltage (see
BOOTING MODES
The ADSP-BF534/ADSP-BF536/ADSP-BF537 processor has six
mechanisms (listed in Table 8) for automatically loading inter-
nal and external memory after a reset. A seventh mode is
provided to execute from external memory, bypassing the boot
sequence.
The BMODE pins of the reset configuration register, sampled
during power-on resets and software-initiated resets, imple-
ment the following modes:
Execute from 16-bit external memory – Execution starts
from address 0x2000 0000 with 16-bit packing. The boot
ROM is bypassed in this mode. All configuration settings
are set for the slowest device possible (3-cycle hold time;
15-cycle R/W access times; 4-cycle setup).
Boot from 8-bit and 16-bit external flash memory – The
8-bit or 16-bit flash boot routine located in Boot ROM
memory space is set up using asynchronous memory
bank 0. All configuration settings are set for the slowest
device possible (3-cycle hold time; 15-cycle R/W access
times; 4-cycle setup). The Boot ROM evaluates the first
byte of the boot stream at address 0x2000 0000. If it is 0x40,
8-bit boot is performed. A 0x60 byte assumes a 16-bit
memory device and performs 8-bit DMA. A 0x20 byte also
assumes 16-bit memory but performs 16-bit DMA.
Boot from serial SPI memory (EEPROM or flash) – 8-, 16-,
or 24-bit addressable devices are supported as well as
AT45DB041, AT45DB081, AT45DB161, AT45DB321,
AT45DB642, and AT45DB1282 DataFlash
devices from
Atmel. The SPI uses the PF10/SPI SSEL1 output pin to
select a single SPI EEPROM/flash device, submits a read
command and successive address bytes (0x00) until a valid
8-, 16-, or 24-bit, or Atmel addressable device is detected,
and begins clocking data into the processor.
Boot from SPI host device – The Blackfin processor oper-
ates in SPI slave mode and is configured to receive the bytes
of the .LDR file from an SPI host (master) agent. To hold
off the host device from transmitting while the boot ROM
is busy, the Blackfin processor asserts a GPIO pin, called
host wait (HWAIT), to signal the host device not to send
any more bytes until the flag is deasserted. The flag is cho-
sen by the user and this information is transferred to the
Blackfin processor via bits 10:5 of the FLAG header.
Boot from UART – Using an autobaud handshake
sequence, a boot-stream-formatted program is downloaded
by the host. The host agent selects a baud rate within the
UART’s clocking capabilities. When performing the auto-
baud, the UART expects an “@” (boot stream) character
(8 bits data, 1 start bit, 1 stop bit, no parity bit) on the RXD
pin to determine the bit rate. It then replies with an
acknowledgement that is composed of 4 bytes: 0xBF, the
value of UART_DLL, the value of UART_DLH, and 0x00.
The host can then download the boot stream. When the
processor needs to hold off the host, it deasserts CTS.
Therefore, the host must monitor this signal.
Table 6. Example System Clock Ratios
Signal Name
SSEL3–0
Divider Ratio
VCO:SCLK
Example Frequency Ratios
(MHz)
VCO
SCLK
0001
1:1
100
0110
6:1
300
50
1010
10:1
500
50
Table 7. Core Clock Ratios
Signal Name
CSEL1–0
Divider Ratio
VCO:CCLK
Example Frequency Ratios
(MHz)
VCO
CCLK
00
1:1
300
01
2:1
300
150
10
4:1
500
125
11
8:1
200
25
Table 8. Booting Modes
BMODE2– 0
Description
000
Execute from 16-bit external memory (bypass
boot ROM)
001
Boot from 8-bit or 16-bit memory
(EPROM/flash)
010
Reserved
011
Boot from serial SPI memory (EEPROM/flash)
100
Boot from SPI host (slave mode)
101
Boot from serial TWI memory (EEPROM/flash)
110
Boot from TWI host (slave mode)
111
Boot from UART host (slave mode)
Table 8. Booting Modes (Continued)
BMODE2–0
Description
相關PDF資料
PDF描述
ECM15DSEI-S243 CONN EDGECARD 30POS .156 EYELET
ADZS-BF518F-EZBRD BOARD EVAL BF512F/14F/16F/18F
ADZS-BF526-EZBRD BOARD EVAL NO DEBUG BF526
GCM18DTBN-S189 CONN EDGECARD 36POS R/A .156 SLD
GCM18DTBH-S189 CONN EDGECARD 36POS R/A .156 SLD
相關代理商/技術參數
參數描述
ADZS-BF537-STAMP 功能描述:SYSTEM DEV FOR ADSP-BF537 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:Blackfin® 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
ADZS-BF537-STAMP 制造商:Analog Devices 功能描述:Microcontroller Development Tool
ADZS-BF538-EZLITE 制造商:Analog Devices 功能描述:- Bulk
ADZSBF538FEZLITE 制造商:Analog Devices 功能描述:RES Wirewound 6927 75Ohm 1% 3W 20PPM SMD T/R
ADZS-BF538F-EZLITE 功能描述:BOARD EVAL FOR ADSP-BF538 RoHS:否 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:Blackfin® 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*