- 您現在的位置：買賣IC網 > PDF目錄11720 > ADUC834BCPZ (Analog Devices Inc)IC MCU 62K FLASH ADC/DAC 56LFCSP PDF資料下載
參數資料
| 型號： | ADUC834BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 連通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外圍設備： | POR，PSM，PWM，溫度傳感器，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 62KB（62K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 數據轉換器： | A/D 3x16b，4x24b; D/A 1x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
REV. A
ADuC834
–13–
MEMORY ORGANIZATION
The ADuC834 contains four different memory blocks, namely:
62 Kbytes of On-Chip Flash/EE Program Memory
4 Kbytes of On-Chip Flash/EE Data Memory
256 bytes of General-Purpose RAM
2 Kbytes of Internal XRAM
(1) Flash/EE Program Memory
The ADuC834 provides 62 Kbytes of Flash/EE program
memory to run user code. The user can choose to run code from
this internal memory or run code from an external program
memory.
If the user applies power or resets the device while the
EA pin is
pulled low externally, the part will execute code from the external
program space; otherwise, if
EA is pulled high externally, the
part defaults to code execution from its internal 62 Kbytes of
Flash/EE program memory.
Unlike the ADuC824, where code execution can overflow from
the internal code space to external code space once the PC
becomes greater than 1FFFH, the ADuC834 does not support
the rollover from F7FFH in internal code space to F800H in
external code space. Instead, the 2048 bytes between F800H
and FFFFH will appear as NOP instructions to user code.
Permanently embedded firmware allows code to be serially
downloaded to the 62 Kbytes of internal code space via the
UART serial port while the device is in-circuit. No external
hardware is required.
56 Kbytes of the program memory can be reprogrammed during
runtime; thus the code space can be upgraded in the field using
a user defined protocol or it can be used as a data memory.
This will be discussed in more detail in the Flash/EE Memory
section of the data sheet.
(2) Flash/EE Data Memory
4 Kbytes of Flash/EE Data Memory are available to the user
and can be accessed indirectly via a group of registers mapped
into the Special Function Register (SFR) area. Access to the
Flash/EE Data memory is discussed in detail later as part of the
Flash/EE Memory section in this data sheet.
(3) General-Purpose RAM
The general-purpose RAM is divided into two separate memories,
namely the upper and the lower 128 bytes of RAM. The lower
128 bytes of RAM can be accessed through direct or indirect
addressing; the upper 128 bytes of RAM can only be accessed
through indirect addressing as it shares the same address space
as the SFR space, which can only be accessed through direct
addressing.
The lower 128 bytes of internal data memory are mapped as
shown in Figure 2. The lowest 32 bytes are grouped into four
banks of eight registers addressed as R0 through R7. The next
16 bytes (128 bits), locations 20H through 2FH above the register
banks, form a block of directly addressable bit locations at bit
addresses 00H through 7FH. The stack can be located anywhere
in the internal memory address space, and the stack depth can
be expanded up to 2048 bytes.
Reset initializes the stack pointer to location 07H. Any CALL
or PUSH pre-increments the SP before loading the stack.
Therefore, loading the stack starts from locations 08H, which is
also the first register (R0) of register bank 1. Thus, if one is
going to use more than one register bank, the stack pointer should
be initialized to an area of RAM not used for data storage.
BIT-ADDRESSABLE
(BIT ADDRESSES)
FOUR BANKS OF EIGHT
REGISTERS
R0–R7
BANKS
SELECTED
VIA
BITS IN PSW
11
10
01
00
07H
0FH
17H
1FH
2FH
7FH
00H
08H
10H
18H
20H
RESET VALUE OF
STACK POINTER
30H
GENERAL-PURPOSE
AREA
Figure 2. Lower 128 Bytes of Internal Data Memory
(4) Internal XRAM
The ADuC834 contains 2 Kbytes of on-chip extended data
memory. This memory, although on-chip, is accessed via the
MOVX instruction. The 2 Kbytes of internal XRAM are
mapped into the bottom 2 Kbytes of the external address space
if the CFG834.0 bit is set. Otherwise, access to the external
data memory will occur just like a standard 8051.
Even with the CFG834.0 bit set, access to the external XRAM
will occur once the 24-bit DPTR is greater than 0007FFH.
EXTERNAL
DATA
MEMORY
SPACE
(24-BIT
ADDRESS
SPACE)
000000H
FFFFFFH
CFG834.0 = 0
EXTERNAL
DATA
MEMORY
SPACE
(24-BIT
ADDRESS
SPACE)
000000H
FFFFFFH
CFG834.0 = 1
0007FFH
000800H
2 KBYTES
ON-CHIP
XRAM
Figure 3. Internal and External XRAM
GENERAL NOTES PERTAINING TO THIS DATA SHEET
1. SET implies a Logic 1 state and CLEARED implies a Logic 0 state unless
otherwise stated.
2. SET and CLEARED also imply that the bit is set or automatically cleared by
the ADuC834 hardware unless otherwise stated.
3. User software should not write 1s to reserved or unimplemented bits as they may
be used in future products.
4. Any pin numbers used throughout this data sheet refer to the 52-lead MQFP
package, unless otherwise stated.
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC845BSZ62-3 | IC MCU FLASH 24BIT ADC 52MQFP |
| ADUC845BSZ62-5 | IC FLASH MCU W/24BIT ADC 52-MQFP |
| PI7C8150BMAIE | IC PCI-PCI BRIDGE ASYNC 208-FQFP |
| VE-B7J-IX-F4 | CONVERTER MOD DC/DC 36V 75W |
| AT89LP51-20JU | MCU 8051 4K FLASH 20MHZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC834BCPZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC834BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 12.58MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +24/16BIT ADC SMD MQFP52 |
| ADUC834BSZ | 功能描述:IC ADC DUAL16/24BIT W/MCU 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC836 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| ADUC836_02 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU |
發布緊急采購，3分鐘左右您將得到回復。