參數資料
型號： ADUC7026BSTZ62I
廠商： Analog Devices Inc
文件頁數： 53/104頁
文件大小： 0K
描述： IC MCU FLASH 62K ANLG I/0 80LQFP
產品培訓模塊： ARM7 Applications & Tools
Intro to ARM7 Core & Microconverters
Process Control
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 44MHz
連通性： EBI/EMI，I²C，SPI，UART/USART
外圍設備： PLA，PWM，PSM，溫度傳感器，WDT
輸入/輸出數： 40
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 2K x 32
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
數據轉換器： A/D 12 x12b; D/A 4x12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 80-LQFP
包裝： 托盤
配用： EVAL-ADUC7026QSPZ-ND - KIT DEV ADUC7026/7027 QUICK PLUS
EVAL-ADUC7026QSZ-ND - KIT DEV FOR ADUC7026/7027
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 52 of 104
SECURITY
The 62 kB of Flash/EE memory available to the user can be read
and write protected.
Bit 31 of the FEEPRO/FEEHIDE MMR (see Table 42) protects
the 62 kB from being read through JTAG programming mode.
The other 31 bits of this register protect writing to the flash
memory. Each bit protects four pages, that is, 2 kB. Write
protection is activated for all types of access.
Three Levels of Protection
Protection can be set and removed by writing directly into
FEEHIDE MMR. This protection does not remain after reset.
Protection can be set by writing into the FEEPRO MMR. It
takes effect only after a save protection command (0x0C)
and a reset. The FEEPRO MMR is protected by a key to
avoid direct access. The key is saved once and must be
entered again to modify FEEPRO. A mass erase sets the
key back to 0xFFFF but also erases all the user code.
Flash can be permanently protected by using the FEEPRO
MMR and a particular value of key: 0xDEADDEAD.
Entering the key again to modify the FEEPRO register
is not allowed.
Sequence to Write the Key
1. Write the bit in FEEPRO corresponding to the page to be
protected.
2. Enable key protection by setting Bit 6 of FEEMOD (Bit 5
must equal 0).
3. Write a 32-bit key in FEEADR and FEEDAT.
4. Run the write key command 0x0C in FEECON; wait for
the read to be successful by monitoring FEESTA.
5. Reset the part.
To remove or modify the protection, the same sequence is used
with a modified value of FEEPRO. If the key chosen is the value
0xDEAD, the memory protection cannot be removed. Only a mass
erase unprotects the part, but it also erases all user code.
The sequence to write the key is illustrated in the following
example (this protects writing Page 4 to Page 7 of the Flash):
FEEPRO=0xFFFFFFFD;
//Protect pages 4 to 7
FEEMOD=0x48;
//Write key enable
FEEADR=0x1234;
//16 bit key value
FEEDAT=0x5678;
//16 bit key value
FEECON= 0x0C;
// Write key command
The same sequence should be followed to protect the part
permanently with FEEADR = 0xDEAD and FEEDAT = 0xDEAD.
FLASH/EE CONTROL INTERFACE
Serial and JTAG programming use the Flash/EE control interface,
which includes the eight MMRs outlined in this section.
Table 31. FEESTA Register
Name
Address
Default Value
Access
FEESTA
0xFFFFF800
0x20
R
FEESTA is a read-only register that reflects the status of the
flash control interface as described in Table 32.
Table 32. FEESTA MMR Bit Designations
Bit
Description
15:6
Reserved.
5
Reserved.
4
Reserved.
3
Flash interrupt status bit. Set automatically when an
interrupt occurs, that is, when a command is complete
and the Flash/EE interrupt enable bit in the FEEMOD
register is set. Cleared when reading the FEESTA register.
2
Flash/EE controller busy. Set automatically when the
controller is busy. Cleared automatically when the
controller is not busy.
1
Command fail. Set automatically when a command
completes unsuccessfully. Cleared automatically when
reading the FEESTA register.
0
Command pass. Set by the MicroConverter when a
command completes successfully. Cleared automatic-
ally when reading the FEESTA register.
Table 33. FEEMOD Register
Name
Address
Default Value
Access
FEEMOD
0xFFFFF804
0x0000
R/W
FEEMOD sets the operating mode of the flash control interface.
Table 34 shows FEEMOD MMR bit designations.
Table 34. FEEMOD MMR Bit Designations
Bit
Description
15:9
Reserved.
8
Reserved. This bit should always be set to 0.
7:5
Reserved. These bits should always be set to 0 except
when writing keys. See the Sequence to Write the Key
section.
4
Flash/EE interrupt enable. Set by user to enable the
Flash/EE interrupt. The interrupt occurs when a
command is complete. Cleared by user to disable
the Flash/EE interrupt.
3
Erase/write command protection. Set by user to
enable the erase and write commands. Cleared to
protect the Flash against the erase/write command.
2:0
Reserved. These bits should always be set to 0.
相關PDF資料
PDF描述
31-320 BNC CONN CRIMP RG-58
D38999/26MC8HN CONN PLUG 8POS STRAIGHT W/PINS
PI7C8154BNAE IC PCI-PCI BRIDGE ASYNC 304-PBGA
ADM1025AARQ IC MONITOR SYS/VOLT 5CH 16QSOP
ADUC832BCPZ IC MCU 62K FLASH ADC/DAC 56LFCSP
相關代理商/技術參數
參數描述
ADUC7026BSTZ62I-RL 功能描述:IC MCU 12BIT 1MSPS I2C 80-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7026BSTZ62-RL 功能描述:IC MCU 12BIT 1MSPS UART 80-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7026HWEI 功能描述:IC MCU 16BIT 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1
ADUC7026HWEI-RL 功能描述:IC MCU 16BIT 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1
ADUC7026HWEIZ 功能描述:IC MCU 16BIT 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*