參數資料
型號： ADT7411ARQ-REEL
廠商： Analog Devices, Inc.
元件分類： 圓形連接器
英文描述： Circular Connector; No. of Contacts:26; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:17-26
中文描述： SPI/I2C兼容，10位數字溫度傳感器和8通道ADC
文件頁數： 23/36頁
文件大?。?/td> 456K
代理商： ADT7411ARQ-REEL
ADT7411
Table 29.
Bit
C0
Rev. A | Page 23 of 36
Function
This bit enables/disables conversions in round robin
and single-channel mode. ADT7411 powers up in round
robin mode, but monitoring is not initiated until this bit
is set. Default = 0.
0 = Stop monitoring.
1 = Start monitoring.
Selects between the two different analog inputs on Pins
7 and 8. The ADT7411 powers up with AIN1 and AIN2
selected.
00: AIN1 and AIN2 selected.
01: Undefined.
10: External TDM selected.
11: Undefined.
Reserved. Write 1 only to this bit.
Reserved. Write 0 only.
0: Enable INT/INT output.
1: Disable INT/INT output.
Configures INT/INT output polarity.
0: Active low.
1: Active high.
Power-Down Bit. Setting this bit to 1 puts the ADT7411
into standby mode. In this mode, the analog circuitry is
fully powered down, but the serial interface is still
operational. To power up the part again, write 0 to this
bit.
C2:C1
C3
C4
C5
C6
PD
Control Configuration 2 Register (Read/Write)
[Address = 19h]
This configuration register is an 8-bit read/write register that is
used to set up some of the operating modes of the ADT7411.
Table 30. Control Configuration 2
D7
D6
D5
D4
C7
C6
C5
C4
0*
0*
0*
0*
*Default settings at power-up.
Table 31.
Bit
Function
C3:0
In single-channel mode, these bits select between V
DD
,
the internal temperature sensor, external temperature
sensor/AIN1, AIN2 to AIN8 for conversion. The default is
V
DD
.
0000 = V
DD
.
0001 = Internal Temperature Sensor.
0010 = External Temperature Sensor/AIN1. (Bits C1:C2 of
Control Configuration 1 affect this selection.)
0011 = AIN2.
0100 = AIN3.
0101 = AIN4.
0110 = AIN5.
0111 = AIN6.
1000 = AIN7.
1001 = AIN8.
D3
C3
0*
D2
C2
0*
D1
C1
0*
D0
C0
0*
Bit
C4
Function
1010 to 1111 = Reserved.
Selects between single-channel and round robin
conversion cycle. Default is round robin.
0 = Round robin.
1 = Single-channel.
Default condition is to average every measurement on all
channels 16 times. This bit disables this averaging.
Channels affected are temperature, analog inputs, and
V
DD
.
0 = Enable averaging.
1 = Disable averaging.
SMBus timeout on the serial clock puts a 25 ms limit on
the pulse width of the clock, ensuring that a fault on the
master SCL does not lock up the SDA line.
0 = Disable SMBus timeout.
1 = Enable SMBus timeout.
Software Reset. Setting this bit to a 1 causes a software
reset. All registers will reset to their default settings.
C5
C6
C7
Control Configuration 3 Register (Read/Write)
[Address = 1Ah]
This configuration register is an 8-bit read/write register that is
used to set up some of the operating modes of the ADT7411.
Table 32. Control Configuration 3
D7
D6
D5
D4
C7
C6
C5
C4
0*
0*
0*
0*
*Default settings at power-up.
Table 33.
Bit
Function
C0
Selects between fast and normal ADC conversion
speeds.
0 = ADC clock at 1.4 kHz.
1 = ADC clock at 22.5 kHz. D+ and D analog filters are
disabled.
C1:2
Reserved. Only write 0s.
C3
Reserved. Write only 1 to this bit.
C4
Selects the ADC reference to be either Internal V
REF
or
V
DD
for analog inputs.
0 = Int V
REF
1 = V
DD
C5:C7
Reserved. Only write 0s.
Interrupt Mask 1 Register (Read/Write) [Address = 1Dh]
This mask register is an 8-bit read/write register that can be
used to mask out any interrupts that can cause the INT/INT pin
to go active.
Table 34. Interrupt Mask 1
D7
D6
D5
D4
D7
D6
D5
D4
0*
0*
0*
0*
D3
C3
1*
D2
C2
0*
D1
C1
0*
D0
C0
0*
D3
D3
0*
D2
D2
0*
D1
D1
0*
D0
D0
0*
*
Default settings at power-up.
相關PDF資料
PDF描述
ADT7411ARQ-REEL7 Circular Connector; No. of Contacts:55; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:17-35
ADT7411ARQZ-REEL Circular Connector; No. of Contacts:55; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:17-35
ADT7411ARQZ-REEL7 Circular Connector; No. of Contacts:55; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:17-35
ADT7411ARQZ10 LJT 6C 6#12 SKT RECP
ADuC812(中文) 12-Bit ADC with Embedded FLASH MCU(12位8通道A/D轉換器)
相關代理商/技術參數
參數描述
ADT7411ARQ-REEL7 功能描述:IC SENSOR TEMP 10BIT ADC 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓撲:ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND
ADT7411ARQZ 功能描述:IC DGTL TEMP SNSR 8CH ADC 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:3,000 系列:- 功能:溫度開關 傳感器類型:內部 感應溫度:85°C 分界點 精確度:±6°C（最小值） 拓撲:ADC（三角積分型），比較器，寄存器庫 輸出類型:開路漏極 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:ADT6501SRJZP085RL7-ND
ADT7411ARQZ 制造商:Analog Devices 功能描述:Temperature Sensor IC
ADT7411ARQZ1 制造商:AD 制造商全稱:Analog Devices 功能描述:SPI??-/I2C??-Compatible, 10-Bit Digital Temperature Sensor and 8-Channel ADC
ADT7411ARQZ10 制造商:AD 制造商全稱:Analog Devices 功能描述:SPI/I2C Compatible, 10-Bit Digital Temperature Sensor and 8-Channel ADC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*