參數資料
型號： ADSP-2186MKCAZ-300
廠商： Analog Devices Inc
文件頁數： 9/40頁
文件大小： 0K
描述： IC DSP CONTROLLER 16BIT 144MBGA
標準包裝： 1
系列： ADSP-21xx
類型： 定點
接口： 主機接口，串行端口
時鐘速率： 75MHz
非易失內存： 外部
芯片上RAM： 40kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 2.50V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 144-LFBGA
供應商設備封裝： 144-迷你型BGA
包裝： 托盤
REV. 0
ADSP-2186M
–17–
PROGRAMMABLE I/O
MODE A/PFO
RESET
ERESET
1k
ADSP-2186M
Figure 12. Mode A Pin/EZ-ICE Circuit
See the ADSP-2100 Family EZ-Tools data sheet for complete
information on ICE products.
The ICE-Port interface consists of the following ADSP-2186M
pins:
EBR, EINT, EE, EBG, ECLK, ERESET, ELIN, EMS,
and ELOUT
These ADSP-2186M pins must be connected only to the EZ-ICE
connector in the target system. These pins have no function except
during emulation, and do not require pull-up or pull-down
resistors. The traces for these signals between the ADSP-2186M
and the connector must be kept as short as possible, no longer
than 3 inches.
The following pins are also used by the EZ-ICE:
BR, BG,
RESET, and GND.
The EZ-ICE uses the EE (emulator enable) signal to take con-
trol of the ADSP-2186M in the target system. This causes the
processor to use its
ERESET, EBR, and EBG pins instead of
the
RESET, BR, and BG pins. The BG output is three-stated.
These signals do not need to be jumper-isolated in your system.
The EZ-ICE connects to your target system via a ribbon cable
and a 14-pin female plug. The female plug is plugged onto the
14-pin connector (a pin strip header) on the target board.
Target Board Connector for EZ-ICE Probe
The EZ-ICE connector (a standard pin strip header) is shown in
Figure 13. You must add this connector to your target board
design if you intend to use the EZ-ICE. Be sure to allow enough
room in your system to fit the EZ-ICE probe onto the 14-pin
connector.
1
2
34
56
7
8
9
10
11
12
13
14
GND
KEY (NO PIN)
RESET
BR
BG
TOP VIEW
EBG
EBR
ELOUT
EE
EINT
ELIN
ECLK
EMS
ERESET
Figure 13. Target Board Connector for EZ-ICE
The 14-pin, 2-row pin strip header is keyed at the Pin 7 loca-
tion—Pin 7 must be removed from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spac-
ing should be 0.1
× 0.1 inches. The pin strip header must have
at least 0.15 inch clearance on all sides to accept the EZ- ICE
probe plug.
Pin strip headers are available from vendors such as 3M,
McKenzie, and Samtec.
Target Memory Interface
For your target system to be compatible with the EZ-ICE
emulator, it must comply with the memory interface guidelines
listed below.
PM, DM, BM, IOM, AND CM
Design your Program Memory (PM), Data Memory (DM), Byte
Memory (BM), I/O Memory (IOM), and Composite Memory
(CM) external interfaces to comply with worst case device tim-
ing requirements and switching characteristics as specified in
this data sheet. The performance of the EZ- ICE may approach
published worst-case specification for some memory access
timing requirements and switching characteristics.
Note: If your target does not meet the worst-case chip specifica-
tion for memory access parameters, you may not be able to
emulate your circuitry at the desired CLKIN frequency. Depend-
ing on the severity of the specification violation, you may have
trouble manufacturing your system as DSP components statisti-
cally vary in switching characteristic and timing requirements
within published limits.
Restriction: All memory strobe signals on the ADSP-2186M
(
RD, WR, PMS, DMS, BMS, CMS, and IOMS) used in your
target system must have 10 k
pull-up resistors connected when
the EZ-ICE is being used. The pull-up resistors are necessary
because there are no internal pull-ups to guarantee their state
during prolonged three-state conditions resulting from typical
EZ-ICE debugging sessions. These resistors may be removed at
your option when the EZ-ICE is not being used.
Target System Interface Signals
When the EZ-ICE board is installed, the performance on some
system signals change. Design your system to be compatible
with the following system interface signal changes introduced by
the EZ-ICE board:
EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the
RESET
signal.
EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the
BR signal.
EZ-ICE emulation ignores
RESET and BR when single-
stepping.
EZ-ICE emulation ignores
RESET and BR when in Emulator
Space (DSP halted).
EZ-ICE emulation ignores the state of target
BR in certain
modes. As a result, the target system may take control of the
DSP’s external memory bus only if bus grant (
BG) is asserted
by the EZ- ICE board’s DSP.
相關PDF資料
PDF描述
GBA24DRMD CONN EDGECARD 48POS .125 SQ WW
GSM44DRTF CONN EDGECARD 88POS DIP .156 SLD
ADSP-2184LBSTZ-160 IC DSP CONTROLLER 16BIT 100LQFP
GMM44DRTF CONN EDGECARD 88POS DIP .156 SLD
ECM12DSEN CONN EDGECARD 24POS .156 EYELET
相關代理商/技術參數
參數描述
ADSP-2186MKST-300 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 75MHz 75MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:75 MHZ 16-BIT DSP,2.5V,8K/8K 2.5V,LQFP - Bulk 制造商:Analog Devices 功能描述:DIGITAL SIGNAL PROCESSOR IC ((NW))
ADSP-2186MKST-300R 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 75MHz 75MIPS 100-Pin LQFP T/R
ADSP-2186MKSTZ-300 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-2186MKSTZ300R 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-2186N 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ADSP-2184N-ADSP-2189N: DSP Microcomputer Data Sheet (Rev. 0. 10/01)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*