- 您現在的位置：買賣IC網 > PDF目錄19396 > ADSP-2186MKCAZ-300 (Analog Devices Inc)IC DSP CONTROLLER 16BIT 144MBGA PDF資料下載
參數資料
| 型號： | ADSP-2186MKCAZ-300 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP CONTROLLER 16BIT 144MBGA |
| 標準包裝： | 1 |
| 系列： | ADSP-21xx |
| 類型： | 定點 |
| 接口： | 主機接口，串行端口 |
| 時鐘速率： | 75MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 40kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 2.50V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LFBGA |
| 供應商設備封裝： | 144-迷你型BGA |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
REV. 0
–16–
ADSP-2186M
These 32 words are used to set up the BDMA to load in the
remaining program code. The BCR bit is also set to 1, which
causes program execution to be held off until all 32 words are
loaded into on-chip program memory. Execution then begins at
address 0.
The ADSP-2100 Family development software (Revision 5.02
and later) fully supports the BDMA booting feature and can
generate byte-memory space-compatible boot code.
The IDLE instruction can also be used to allow the processor
to hold off execution while booting continues through the
BDMA interface. For BDMA accesses while in Host Mode, the
addresses to boot memory must be constructed externally to the
ADSP-2186M. The only memory address bit provided by the
processor is A0.
IDMA Port Booting
The ADSP-2186M can also boot programs through its Internal
DMA port. If Mode C = 1, Mode B = 0, and Mode A = 1, the
ADSP-2186M boots from the IDMA port. IDMA feature can
load as much on-chip memory as desired. Program execution is
held off until on-chip program memory location 0 is written to.
Bus Request and Bus Grant
The ADSP-2186M can relinquish control of the data and address
buses to an external device. When the external device requires
access to memory, it asserts the bus request (
BR) signal. If the
ADSP-2186M is not performing an external memory access, it
responds to the active
BR input in the following processor cycle by:
Three-stating the data and address buses and the
PMS, DMS,
BMS, CMS, IOMS, RD, WR output drivers,
Asserting the bus grant (
BG) signal, and
Halting program execution.
If Go Mode is enabled, the ADSP-2186M will not halt program
execution until it encounters an instruction that requires an
external memory access.
If the ADSP-2186M is performing an external memory access
when the external device asserts the
BR signal, it will not three-
state the memory interfaces nor assert the
BG signal until the
processor cycle after the access completes. The instruction does
not need to be completed when the bus is granted. If a single
instruction requires two external memory accesses, the bus will
be granted between the two accesses.
When the
BR signal is released, the processor releases the BG
signal, re-enables the output drivers, and continues program
execution from the point at which it stopped.
The bus request feature operates at all times, including when
the processor is booting and when
RESET is active.
The
BGH pin is asserted when the ADSP-2186M requires the
external bus for a memory or BDMA access, but is stopped.
The other device can release the bus by deasserting bus request.
Once the bus is released, the ADSP-2186M deasserts
BG and
BGH and executes the external memory access.
Flag I/O Pins
The ADSP-2186M has eight general purpose programmable
input/output flag pins. They are controlled by two memory
mapped registers. The PFTYPE register determines the direc-
tion, 1 = output and 0 = input. The PFDATA register is used to
read and write the values on the pins. Data being read from a
pin configured as an input is synchronized to the ADSP-2186M’s
clock. Bits that are programmed as outputs will read the value
being output. The PF pins default to input during reset.
In addition to the programmable flags, the ADSP-2186M has five
fixed-mode flags, FI, FO, FL0, FL1, and FL2. FL0–FL2 are
dedicated output flags. FI and FO are available as an alternate
configuration of SPORT1.
Note: Pins PF0, PF1, PF2, and PF3 are also used for device
configuration during reset.
Instruction Set Description
The ADSP-2186M assembly language instruction set has an
algebraic syntax that was designed for ease of coding and read-
ability. The assembly language, which takes full advantage of the
processor’s unique architecture, offers the following benefits:
The algebraic syntax eliminates the need to remember cryptic
assembler mnemonics. For example, a typical arithmetic add
instruction, such as AR = AX0 + AY0, resembles a simple
equation.
Every instruction assembles into a single, 24-bit word that
can execute in a single instruction cycle.
The syntax is a superset ADSP-2100 Family assembly lan-
guage and is completely source and object code compatible
with other family members. Programs may need to be relocated
to utilize on-chip memory and conform to the ADSP-2186M’s
interrupt vector and reset vector map.
Sixteen condition codes are available. For conditional jump,
call, return, or arithmetic instructions, the condition can
be checked and the operation executed in the same instruc-
tion cycle.
Multifunction instructions allow parallel execution of an
arithmetic instruction with up to two fetches or one write to
processor memory space during a single instruction cycle.
DESIGNING AN EZ-ICE-COMPATIBLE SYSTEM
The ADSP-2186M has on-chip emulation support and an
ICE-Port, a special set of pins that interface to the EZ-ICE.
These features allow in-circuit emulation without replacing the
target system processor by using only a 14-pin connection from
the target system to the EZ-ICE. Target systems must have a
14-pin connector to accept the EZ-ICE’s in-circuit probe, a
14-pin plug.
Issuing the chip reset command during emulation causes the
DSP to perform a full chip reset, including a reset of its memory
mode. Therefore, it is vital that the mode pins are set correctly
PRIOR to issuing a chip reset command from the emulator user
interface. If a passive method of maintaining mode information is
being used (as discussed in Setting Memory Modes), it does not
matter that the mode information is latched by an emulator
reset. However, if the
RESET pin is being used as a method of
setting the value of the mode pins, the effects of an emulator
reset must be taken into consideration.
One method of ensuring that the values located on the mode
pins are those desired is to construct a circuit like the one shown
in Figure 12. This circuit forces the value located on the Mode
A pin to logic high; regardless of whether it is latched via the
RESET or ERESET pin.
相關PDF資料 |
PDF描述 |
|---|---|
| GBA24DRMD | CONN EDGECARD 48POS .125 SQ WW |
| GSM44DRTF | CONN EDGECARD 88POS DIP .156 SLD |
| ADSP-2184LBSTZ-160 | IC DSP CONTROLLER 16BIT 100LQFP |
| GMM44DRTF | CONN EDGECARD 88POS DIP .156 SLD |
| ECM12DSEN | CONN EDGECARD 24POS .156 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2186MKST-300 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 75MHz 75MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:75 MHZ 16-BIT DSP,2.5V,8K/8K 2.5V,LQFP - Bulk 制造商:Analog Devices 功能描述:DIGITAL SIGNAL PROCESSOR IC ((NW)) |
| ADSP-2186MKST-300R | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 75MHz 75MIPS 100-Pin LQFP T/R |
| ADSP-2186MKSTZ-300 | 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-2186MKSTZ300R | 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-2186N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ADSP-2184N-ADSP-2189N: DSP Microcomputer Data Sheet (Rev. 0. 10/01) |
發布緊急采購，3分鐘左右您將得到回復。