- 您現在的位置：買賣IC網 > PDF目錄19381 > ADSP-2183BSTZ-160 (Analog Devices Inc)IC DSP CONTROLLER 16BIT 128LQFP PDF資料下載
參數資料
| 型號： | ADSP-2183BSTZ-160 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 27/31頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP CONTROLLER 16BIT 128LQFP |
| 產品變化通告： | Mold Change 11/Jul/2012 |
| 標準包裝： | 1 |
| 系列： | ADSP-21xx |
| 類型： | 定點 |
| 接口： | 同步串行端口（SSP） |
| 時鐘速率： | 40MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 80kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 3.30V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-LQFP |
| 供應商設備封裝： | 128-TQFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁
ADSP-2183
–5–
REV. C
Table I. Interrupt Priority and Interrupt Vector Addresses
Interrupt Vector
Source of Interrupt
Address (Hex)
Reset (or Power-Up with PUCR = 1) 0000
(Highest Priority)
Power-Down (Nonmaskable)
002C
IRQ2
0004
IRQL1
0008
IRQL0
000C
SPORT0 Transmit
0010
SPORT0 Receive
0014
IRQE
0018
BDMA Interrupt
001C
SPORT1 Transmit or
IRQ1
0020
SPORT1 Receive or
IRQ0
0024
Timer
0028
(Lowest Priority)
Interrupt routines can either be nested, with higher priority
interrupts taking precedence, or processed sequentially. Inter-
rupts can be masked or unmasked with the IMASK register.
Individual interrupt requests are logically ANDed with the bits
in IMASK; the highest priority unmasked interrupt is then
selected. The power-down interrupt is nonmaskable.
The ADSP-2183 masks all interrupts for one instruction cycle
following the execution of an instruction that modifies the
IMASK register. This does not affect serial port autobuffering
or DMA transfers.
The interrupt control register, ICNTL, controls interrupt nest-
ing and defines the
IRQ0, IRQ1 and IRQ2 external interrupts to
be either edge- or level-sensitive. The
IRQE pin is an external
edge-sensitive interrupt and can be forced and cleared. The
IRQL0 and IRQL1 pins are external level-sensitive interrupts.
The IFC register is a write-only register used to force and clear
interrupts.
On-chip stacks preserve the processor status and are automati-
cally maintained during interrupt handling. The stacks are
twelve levels deep to allow interrupt, loop and subroutine nesting.
The following instructions allow global enable or disable servic-
ing of the interrupts (including power down), regardless of the
state of IMASK. Disabling the interrupts does not affect serial
port autobuffering or DMA.
ENA INTS;
DIS INTS;
When the processor is reset, interrupt servicing is enabled.
LOW POWER OPERATION
The ADSP-2183 has three low power modes that significantly
reduce the power dissipation when the device operates under
standby conditions. These modes are:
Power-Down
Idle
Slow Idle
The CLKOUT pin may also be disabled to reduce external
power dissipation.
Power-Down
The ADSP-2183 processor has a low power feature that lets
the processor enter a very low power dormant state through
hardware or software control. Here is a brief list of power-
down features. Refer to the ADSP-2100 Family User’s Manual,
Third Edition, “System Interface” chapter for detailed
information about the power-down feature.
Quick recovery from power-down. The processor begins
executing instructions in as few as 300 CLKIN cycles.
Support for an externally generated TTL or CMOS
processor clock. The external clock can continue running
during power-down without affecting the lowest power
rating and 300 CLKIN cycle recovery.
Support for crystal operation includes disabling the oscil-
lator to save power (the processor automatically waits 4096
CLKIN cycles for the crystal oscillator to start and stabi-
lize), and letting the oscillator run to allow 300 CLKIN
cycle start-up.
Power-down is initiated by either the power-down pin
(
PWD) or the software power-down force bit.
Interrupt support allows an unlimited number of instruc-
tions to be executed before optionally powering down.
The power-down interrupt also can be used as a non-
maskable, edge-sensitive interrupt.
Context clear/save control allows the processor to con-
tinue where it left off or start with a clean context when
leaving the power-down state.
The
RESET pin also can be used to terminate
power-down.
Power-down acknowledge pin indicates when the
processor has entered power-down.
Idle
When the ADSP-2183 is in the Idle Mode, the processor
waits indefinitely in a low power state until an interrupt
occurs. When an unmasked interrupt occurs, it is serviced;
execution then continues with the instruction following the
IDLE instruction.
Slow Idle
The IDLE instruction is enhanced on the ADSP-2183 to
let the processor’s internal clock signal be slowed, further
reducing power consumption. The reduced clock frequency,
a programmable fraction of the normal clock rate, is speci-
fied by a selectable divisor given in the IDLE instruction.
The format of the instruction is
IDLE (n);
where n = 16, 32, 64 or 128. This instruction keeps the
processor fully functional, but operating at the slower clock
rate. While it is in this state, the processor’s other internal
clock signals, such as SCLK, CLKOUT and timer clock,
are reduced by the same ratio. The default form of the
instruction, when no clock divisor is given, is the standard
IDLE instruction.
相關PDF資料 |
PDF描述 |
|---|---|
| GEM10DSUH | CONN EDGECARD 20POS DIP .156 SLD |
| TAJC226M016H | CAP TANT 22UF 16V 20% 2312 |
| ADSP-BF561SBB500 | IC PROCESSOR 500MHZ 297PBGA |
| VI-B2J-CY-F2 | CONVERTER MOD DC/DC 36V 50W |
| TPSD107K010R0150 | CAP TANT 100UF 10V 10% 2917 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2183KCA-133 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADSP-2183KCA-210 | 功能描述:IC DSP CONTROLLER 16BIT 144MBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-2183KCAZ-210 | 功能描述:IC DSP 16BIT 52MHZ 144-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP2183KS133 | 制造商:AD 功能描述:* |
| ADSP-2183KST-115 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。