參數資料
型號： ADSP-21262SKBC-200
廠商： ANALOG DEVICES INC
元件分類： 數字信號處理
英文描述： SHARC Processor
中文描述： 16-BIT, 66.67 MHz, OTHER DSP, PBGA136
封裝： MO-205AE, BGA-136
文件頁數： 16/44頁
文件大小： 1295K
代理商： ADSP-21262SKBC-200
Rev. A
|
Page 16 of 44
|
May 2004
ADSP-21262
ABSOLUTE MAXIMUM RATINGS
ESD SENSITIVITY
TIMING SPECIFICATIONS
The ADSP-21262’s internal clock (a multiple of CLKIN) pro-
vides the clock signal for timing internal memory, processor
core, serial ports, and parallel port (as required for read/write
strobes in asynchronous access mode). During reset, program
the ratio between the DSP’s internal clock frequency and exter-
nal (CLKIN) clock frequency with the CLKCFG1-0 pins. To
determine switching frequencies for the serial ports, divide
down the internal clock, using the programmable divider con-
trol of each port (DIVx for the serial ports).
The ADSP-21262’s internal clock switches at higher frequencies
than the system input clock (CLKIN). To generate the internal
clock, the DSP uses an internal phase-locked loop (PLL). This
PLL-based clocking minimizes the skew between the system
clock (CLKIN) signal and the DSP’s internal clock (the clock
source for the parallel port logic and I/O pads).
Note the definitions of various clock periods that are a function
of CLKIN and the appropriate ratio control (
Table 7
and
Table 8
).
Figure 5
shows Core to CLKIN ratios of 3:1, 8:1, and 16:1 with
external oscillator or crystal. Note that more ratios are possible
and can be set through software using the power management
control register (PMCTL). For more information, see the
ADSP-2126x SHARC DSP Core Manual
.
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results
for an individual device, the values given in this data sheet
reflect statistical variations and worst cases. Consequently, it is
not meaningful to add parameters to derive longer times.
See
Figure 30 on Page 37
under Test conditions for voltage ref-
erence levels.
Parameter
Internal (Core) Supply Voltage (V
DDINT
)
1
Analog (PLL) Supply Voltage (A
VDD
)
1
External (I/O) Supply Voltage (V
DDEXT
)
1
Input Voltage–0.5 V to V
DDEXT1
Output Voltage Swing–0.5 V to V
DDEXT1
Load Capacitance
1
Storage Temperature Range
1
Junction Temperature under Bias
Rating
–0.3 V to +1.4 V
–0.3 V to +1.4 V
–0.3 V to +3.8 V
+ 0.5 V
+ 0.5 V
200 pF
–65
°
C to +150
°
C
125
°
C
1
Stresses greater than those listed above may cause permanent damage to the device. These are stress ratings only;
functional operation of the device at these or any other conditions greater than those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods
may affect device reliability.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADSP-21262 features proprietary ESD protection circuitry, permanent
damage may occur on devices subjected to high energy electrostatic discharges. Therefore,
proper ESD precautions are recommended to avoid performance degradation or loss of
functionality.
Table 7. ADSP-21262 CLKOUT and CCLK Clock
Generation Operation
Timing
Requirements
CLKIN
CCLK
Description
Calculation
Input Clock
Core Clock
1/t
CK
1/t
CCLK
Table 8. Clock Periods
Timing
Requirements
t
CK
t
CCLK
t
SCLK
t
SPICLK
Description
1
CLKIN Clock Period
(Processor) Core Clock Period
Serial Port Clock Period = (t
CCLK
) × SR
SPI Clock Period = (t
CCLK
) × SPIR
1
where:
SR = serial port-to-core clock ratio (wide range, determined by
SPORT CLKDIV)
SPIR = SPI-to-Core Clock Ratio (wide range, determined by
SPIBAUD register)
DAI_Px = Serial Port Clock
SPICLK = SPI Clock
相關PDF資料
PDF描述
ADSP-21262SKBCZ200 SHARC Processor
ADSP-21266 SHARC Embedded Processor
ADSP-21266SKBC-2B SHARC Embedded Processor
ADSP-21266SKBCZ-2B SHARC Embedded Processor
ADSP-21266SKBCZ-2C SHARC Embedded Processor
相關代理商/技術參數
參數描述
ADSP-21262SKBC200R 制造商:Analog Devices 功能描述:DSP Floating-Point 32-Bit 200MHz 200MIPS 136-Pin CSP-BGA T/R
ADSP-21262SKBC-200X 制造商:Analog Devices 功能描述:
ADSP-21262SKBCZ200 功能描述:IC DSP CTLR 32BIT 136CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-21262SKBCZ200 制造商:Analog Devices 功能描述:DIGITAL SIGNAL PROCESSOR IC
ADSP21262SKBCZ200R 功能描述:IC DSP CTLR 32BIT 136CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*