參數資料
型號： ADSP-21062KS-133
廠商： Analog Devices Inc
文件頁數： 4/64頁
文件大?。?/td> 0K
描述： IC DSP CONTROLLER 32BIT 240MQFP
產品培訓模塊： SHARC Processor Overview
標準包裝： 1
系列： SHARC®
類型： 浮點
接口： 主機接口，連接端口，串行端口
時鐘速率： 33MHz
非易失內存： 外部
芯片上RAM： 256kB
電壓 - 輸入/輸出： 5.00V
電壓 - 核心： 5.00V
工作溫度： 0°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 240-BFQFP 裸露焊盤
供應商設備封裝： 240-MQFP-EP（32x32）
包裝： 托盤
Rev. F
|
Page 12 of 64
|
March 2008
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
TFSx
I/O
Transmit Frame Sync (Serial Ports 0, 1).
RFSx
I/O
Receive Frame Sync (Serial Ports 0, 1).
LxDAT3–0
I/O
Link Port Data (Link Ports 0–5). Each LxDAT pin has a 50 k
: internal pull-down resistor that is enabled or
disabled by the LPDRD bit of the LCOM register.
LxCLK
I/O
Link Port Clock (Link Ports 0–5). Each LxCLK pin has a 50 k
: internal pull-down resistor that is enabled or
disabled by the LPDRD bit of the LCOM register.
LxACK
I/O
Link Port Acknowledge (Link Ports 0–5). Each LxACK pin has a 50 k
: internal pull-down resistor that is
enabled or disabled by the LPDRD bit of the LCOM register.
EBOOT
I
EPROM Boot Select. When EBOOT is high, the ADSP-2106x is configured for booting from an 8-bit EPROM.
When EBOOT is low, the LBOOT and BMS inputs determine booting mode. See the table in the BMS pin
description below. This signal is a system configuration selection that should be hardwired.
LBOOT
I
Link Boot. When LBOOT is high, the ADSP-2106x is configured for link port booting. When LBOOT is low,
the ADSP-2106x is configured for host processor booting or no booting. See the table in the BMS pin
description below. This signal is a system configuration selection that should be hardwired.
BMS
I/OT
Boot Memory Select. Output: Used as chip select for boot EPROM devices (when EBOOT = 1, LBOOT = 0).
In a multiprocessor system, BMS is output by the bus master.
Input: When low, indicates that no booting will
occur and that ADSP-2106x will begin executing instructions from external memory. See table below. This
input is a system configuration selection that should be hardwired. *Three-statable only in EPROM boot
mode (when BMS is an output).
EBOOT
LBOOT
BMS
Booting Mode
1
0
Output
EPROM (Connect BMS to EPROM chip select.)
0
1 (Input)
Host Processor
0
1
1 (Input)
Link Port
0
0 (Input)
No Booting. Processor executes from external memory.
01
0 (Input)
Reserved
1
x (Input)
Reserved
CLKIN
I
Clock In. External clock input to the ADSP-2106x. The instruction cycle rate is equal to CLKIN. CLKIN should
not be halted, changed, or operated below the minimum specified frequency.
RESET
I/A
Processor Reset. Resets the ADSP-2106x to a known state and begins program execution at the program
memory location specified by the hardware reset vector address. This input must be asserted (low) at
power-up.
TCK
I
Test Clock (JTAG). Provides an asynchronous clock for JTAG boundary scan.
TMS
I/S
Test Mode Select (JTAG). Used to control the test state machine. TMS has a 20 k
: internal pull-up resistor.
TDI
I/S
Test Data Input (JTAG). Provides serial data for the boundary scan logic. TDI has a 20 k
: internal pull-up
resistor.
TDO
O
Test Data Output (JTAG). Serial scan output of the boundary scan path.
TRST
I/A
Test Reset (JTAG). Resets the test state machine. TRST must be asserted (pulsed low) after power-up or held
low for proper operation of the ADSP-2106x. TRST has a 20 k
: internal pull-up resistor.
EMU
O
Emulation Status. Must be connected to the ADSP-2106x EZ-ICE target board connector only.
ICSA
O
Reserved, leave unconnected.
VDD
P
Power Supply; nominally 5.0 V dc for 5 V devices or 3.3 V dc for 3.3 V devices. (30 pins).
GND
G
Power Supply Return. (30 pins).
NC
Do Not Connect. Reserved pins which must be left open and unconnected.
Table 3. Pin Descriptions (Continued)
Pin
Type
Function
A = Asynchronous, G = Ground, I = Input, O = Output, P = Power Supply, S = Synchronous, (A/D) = Active Drive, (O/D) = Open Drain,
T = Three-State (when SBTS is asserted, or when the ADSP-2106x is a bus slave)
相關PDF資料
PDF描述
VI-B3M-CY-F2 CONVERTER MOD DC/DC 10V 50W
5723-RC CHOKE RF HI CURR 1800UH 15% RAD
VI-B3L-CY-F3 CONVERTER MOD DC/DC 28V 50W
MAX6670AUB70+ IC TEMP SENSOR REMOTE 10-UMAX
747871-4 CONN D-SUB PLUG VERT 9POS
相關代理商/技術參數
參數描述
ADSP21062KS160 制造商:AD 功能描述:New
ADSP-21062KS-160 功能描述:IC DSP CONTROLLER 2MBIT 240MQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21062KSZ-133 功能描述:IC DSP CONTROLLER 32BIT 240MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-21062KSZ-160 功能描述:IC DSP CONTROLLER 32BIT 240MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21062L 制造商:AD 制造商全稱:Analog Devices 功能描述:ADSP-2106x SHARC DSP Microcomputer Family
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*