參數資料
型號： ADS5541
英文描述： MOSFET, N SC-75AMOSFET, N SC-75A; Transistor type:MOSFET; Transistor polarity:N; Voltage, Vds max:20V; Case style:SC-75A; Current, Id cont:0.14A; Current, Idm pulse:0.5A; Power, Pd:0.25W; Resistance, Rds on:10R; SMD:1; Depth,
中文描述： 14位，80Msps模擬到數字轉換器
文件頁數： 21/30頁
文件大?。?/td> 401K
代理商： ADS5541
SBAS308A MAY 2004 REVISED MARCH 2005
www.ti.com
21
This differential input topology produces a high level of
AC performance for high sampling rates. It also results
in a very high usable input bandwidth, especially
important for high intermediate-frequency (IF) or
undersampling applications. The ADS5542 requires
each of the analog inputs (INP, INM) to be externally
biased around the common-mode level of the internal
circuitry (CM, pin 17). For a full-scale differential input,
each of the differential lines of the input signal (pins 19
and 20) swings symmetrically between CM + 0.575V
and CM – 0.575V. This means that each input is driven
with a signal of up to CM
±
0.575V, so that each input
has a maximum differential signal of 1.15V
PP
for a total
differential input signal swing of 2.3V
PP
. The maximum
swing is determined by the two reference voltages, the
top reference (REFP, pin 29), and the bottom reference
(REFM, pin 30).
The ADS5542 obtains optimum performance when the
analog inputs are driven differentially. The circuit shown
in Figure 38 shows one possible configuration using an
RF transformer.
R
0
50
Z
0
50
1:1
INP
ADS5542
INM
CM
ADT11WT
R
50
1nF
0.1
μ
F
AC Signal
Source
10
25
25
Figure 38. Transformer Input to Convert
Single-Ended Signal to Differential Signal
The single-ended signal is fed to the primary winding of
an RF transformer. Placing a 25
resistor in series with
INP and INM is recommended to dampen ringing due
to ADC kickback. Since the input signal must be biased
around the common-mode voltage of the internal
circuitry, the common-mode voltage (V
CM
) from the
ADS5542 is connected to the center-tap of the
secondary winding. To ensure a steady low-noise V
CM
reference, best performance is attained when the CM
output (pin 17) is filtered to ground with a 10
series
resistor and parallel 0.1
μ
F and 0.001
μ
F low-inductance
capacitors, as illustrated in Figure 37.
Output V
CM
(pin 17) is designed to directly drive the
ADC input. When providing a custom CM level, be
aware that the input structure of the ADC sinks a
common-mode current in the order of 400
μ
A (200
μ
A
per input). Equation (1) describes the dependency of
the common-mode current and the sampling
frequency:
400 A
f
S
(in MSPS)
80 MSPS
Where:
f
S
> 10MSPS.
This equation helps to design the output capability and
impedance of the driving circuit accordingly.
When it is necessary to buffer or apply a gain to the
incoming analog signal, it is possible to combine
single-ended operational amplifiers with an RF
transformer, or to use a differential input/output
amplifier without a transformer, to drive the input of the
ADS5542. TI offers a wide selection of single-ended
operational amplifiers (including the THS3201,
THS3202, OPA847, and OPA695) that can be selected
depending on the application. An RF gain block
amplifier, such as TI’s THS9001, can also be used with
an RF transformer for very high input frequency
applications. The THS4503 is a recommended
differential input/output amplifier. Table 4 lists the
recommended amplifiers.
When using single-ended operational amplifiers (such
as the THS3201, THS3202, OPA847, or OPA695) to
provide gain, a three-amplifier circuit is recommended
with one amplifier driving the primary of an RF
transformer and one amplifier in each of the legs of the
secondary driving the two differential inputs of the
ADS5542. These three amplifier circuits minimize
even-order harmonics. For very high frequency inputs,
an RF gain block amplifier can be used to drive a
transformer primary; in this case, the transformer
secondary connections can drive the input of the
ADS5542 directly, as shown in Figure 38, or with the
addition of the filter circuit shown in Figure 39.
Figure 39 illustrates how R
IN
and C
IN
can be placed to
isolate the signal source from the switching inputs of the
ADC and to implement a low-pass RC filter to limit the
input noise in the ADC. It is recommended that these
components be included in the ADS5542 circuit layout
when any of the amplifier circuits discussed previously
are used. The components allow fine-tuning of the
circuit performance. Any mismatch between the
differential lines of the ADS5542 input produces a
degradation in performance at high input frequencies,
mainly characterized by an increase in the even-order
harmonics. In this case, special care should be taken to
keep as much electrical symmetry as possible between
both inputs.
(1)
相關PDF資料
PDF描述
ADS5542 14-Bit, 80MSPS Analog-to-Digital Converter
ADS5520 14-Bit, 80MSPS Analog-to-Digital Converter
ADS5521IPAP 12-Bit, 105MSPS Analog-toDigital Converter
ADS5521IPAPR 12-Bit, 105MSPS Analog-toDigital Converter
ADS574 Microprocessor-Compatible Sampling CMOS ANALOG-TO-DIGITAL CONVERTER
相關代理商/技術參數
參數描述
ADS5541EVM 功能描述:數據轉換 IC 開發工具 ADS5541 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
ADS5541IPAP 功能描述:模數轉換器 - ADC 14-Bit 105MSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADS5541IPAPG4 功能描述:模數轉換器 - ADC 14-Bit 105MSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADS5541IPAPR 功能描述:模數轉換器 - ADC 14-Bit 105MSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADS5541IPAPRG4 功能描述:模數轉換器 - ADC 14-Bit 105MSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*