- 您現在的位置：買賣IC網 > PDF目錄366333 > ADNK-3080 (Avago Technologies Ltd.) High-Performance Optical Mouse Sensor PDF資料下載
參數資料
| 型號： | ADNK-3080 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | High-Performance Optical Mouse Sensor |
| 中文描述： | 高性能光學鼠標傳感器 |
| 文件頁數： | 6/39頁 |
| 文件大小： | 655K |
| 代理商： | ADNK-3080 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
6
PCB Assembly Considerations
Figure 5. Exploded view drawing
1. Insert the sensor and all other electrical components
into PCB.
2. Insert the LED into the assembly clip and bend the
leads 90 degrees.
3. Insert the LED/clip assembly into PCB.
4. Wave Solder the entire assembly in a no-wash solder
process utilizing solder fixture. The solder fixture is
needed to protect the sensor during the solder process.
It also sets the correct sensor-to -PCB distance as the
lead shoulders do not normally rest on the PCB surface.
The fixture should be designed to expose the sensor
leads to solder while shielding the optical aperture
from direct solder contact.
5. Place the lens onto the base plate.
Customer supplied base
plate with recommended
alignment features per
IGES drawing.
ADNS-2120 (Lens)
Customer supplied PCB
ADNS-3080 (Sensor)
ADNS-2220 (Clip)
HLMP-ED80-XX000 (LED)
Figure 6. Block diagram of ADNS-3080 optical mouse sensor
IMAGE
PROCESSOR
REFERENCE
VOLTAGE
FILTER NODE
3.3 V POWER
REFB
REFC
GND
RESONATOR
OSC_IN
OSC_OUT
MOSI
NCS
SCLK
OPTP
V
DD3
MISO
LED_CTRL
RESET
NPD
V
A
S
CTRL
OSCILLATOR
6. Remove the protective kapton tape from optical
aperture of the sensor. Care must be taken to keep
contaminants from entering the aperture. During
mouse assembly process, it is recommended that the
PCB is held vertically when kapton tapes are being
removed.
7. Insert PCB assembly over the lens onto the base plate
aligning post to retain PCB assembly. The sensor ap-
erture ring should self-align to the lens.
8. The optical position reference for the PCB is set by the
base plate and lens. Note that the PCB motion due to
button presses must be minimized to maintain optical
alignment.
9. Install mouse top case. There MUST be a feature in the
top case to press down
相關PDF資料 |
PDF描述 |
|---|---|
| ADNS-3080 | High-Performance Optical Mouse Sensor |
| ADNS-3150-001 | Optical Mouse Designer’s Kit |
| ADNS-5020-EN | Optical Mouse Sensor |
| ADNS-5030 | Low Power Optical Mouse Sensor |
| ADNS-5100 | Solid-State Optical Mouse Lens |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNK-3083 | 功能描述:光學傳感器開發工具 Reference Design Kit RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
| ADNK-3530 | 功能描述:光學傳感器開發工具 Sample Kit for ADNS-3530 RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
| ADNK-3533-TN24 | 功能描述:光學傳感器開發工具 Reference Design for ADNS-3530 RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
| ADNK-3550 | 功能描述:光學傳感器開發工具 Sample Kit for ADNS-3550 RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
| ADNK-5000 | 功能描述:光學傳感器開發工具 Sample Kit for ADNS-5000 RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。