- 您現在的位置：買賣IC網 > PDF目錄366333 > ADNK-3080 (Avago Technologies Ltd.) High-Performance Optical Mouse Sensor PDF資料下載
參數資料
| 型號： | ADNK-3080 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | High-Performance Optical Mouse Sensor |
| 中文描述： | 高性能光學鼠標傳感器 |
| 文件頁數： | 15/39頁 |
| 文件大?。?/td> | 655K |
| 代理商： | ADNK-3080 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
15
Synchronous Serial Port
The synchronous serial port is used to set and read pa-
rameters in the ADNS-3080, and to read out the motion
information. The serial port is also used to load SROM
data into the ADNS-3080.
The port is a four-wire, serial port. The host micro-con-
troller always initiates communication; the ADNS-3080
never initiates data transfers. The serial port cannot be
activated while the chip is in power down mode (NPD
low) or reset (RESET high). SCLK, MOSI, and NCS may be
driven directly by a 3.3V output from a micro-controller,
or they may be placed in an open drain configuration by
enabling on-chip pull-up current sources. The open drain
drive allows the use of a 5V micro-controller without any
level shifting components. The port pins may be shared
with other SPI slave devices. When the NCS pin is high,
the inputs are ignored and the output is tri-stated.
The lines which comprise the SPI port are:
SCLK: Clock input. It is always generated by the master
(the micro- controller).
MOSI: Input data (Master Out/Slave In).
MISO: Output data (Master In/Slave Out).
NCS: Chip select input (active low).
NCS needs to be low to activate the serial port; otherwise,
MISO will be high-Z, and MOSI & SCLK will be ignored.
NCS can also be used to reset the serial port in case of
an error.
Chip Select Operation
The serial port is activated after NCS goes low. If NCS
is raised during a transaction, the entire transaction is
aborted and the serial port will be reset. This is true
for all transactions including SROM download. After a
transaction is aborted, the normal address-to-data or
transaction-to-transaction delay is still required before
beginning the next transaction. To improve communica-
tion reliability, all serial transactions should be framed by
NCS. In other words, the port should not remain enabled
during periods of non-use because ESD and EFT/B events
could be interpreted as serial communication and put
the chip into an unknown state. In addition, NCS must
be raised after each burst-mode transaction is complete
to terminate burst-mode. The port is not available for
further use until burst-mode is terminated.
相關PDF資料 |
PDF描述 |
|---|---|
| ADNS-3080 | High-Performance Optical Mouse Sensor |
| ADNS-3150-001 | Optical Mouse Designer’s Kit |
| ADNS-5020-EN | Optical Mouse Sensor |
| ADNS-5030 | Low Power Optical Mouse Sensor |
| ADNS-5100 | Solid-State Optical Mouse Lens |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNK-3083 | 功能描述:光學傳感器開發工具 Reference Design Kit RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
| ADNK-3530 | 功能描述:光學傳感器開發工具 Sample Kit for ADNS-3530 RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
| ADNK-3533-TN24 | 功能描述:光學傳感器開發工具 Reference Design for ADNS-3530 RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
| ADNK-3550 | 功能描述:光學傳感器開發工具 Sample Kit for ADNS-3550 RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
| ADNK-5000 | 功能描述:光學傳感器開發工具 Sample Kit for ADNS-5000 RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。