參數資料
型號： ADM1031ARQ
廠商： ON SEMICONDUCTOR
元件分類： 溫度/濕度傳感器
英文描述： DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
封裝： MO-137AB, QSOP-16
文件頁數： 24/35頁
文件大?。?/td> 368K
代理商： ADM1031ARQ
ADM1031
Rev. 3 | Page 30 of 35 | www.onsemi.com
Table 18. Register 0×00 Configuration Register 1 Power-On Default = 90H
Bit
Name
R/W
Description
0
MONITOR
Read/Write
Setting this bit to a “1” enables monitoring of temperature and enables measurement of the fan tach
signals. (Power-Up Default=0)
1
INT Enable
Read/Write
Setting this bit to a “1” enables the INT output. 1= Enabled 0= Disabled (Power-Up Default=0)
2
TACH/AIN
Read/Write
Clearing this bit to “0” selects digital fan speed measurement via the TACH pins. Setting this bit to “1”
configures the TACH pins as analog inputs that can measure the speed of 2-wire fans via a sense resistor.
(Power-Up Default=0)
3
PWM Invert
Read/Write
Setting this bit to “1” inverts the PWM signal on the output pins. (Power-Up Default=0)
4
Fan Fault
Enable
Read/Write
Logic 1 enables FAN_FAULT pin; Logic 0 disables FAN_FAULT output. (Power-Up Default=1)
6-
5
PWM Mode
Read/Write
These two bits control the behavior of the fans in auto fan speed control mode.
00 = Remote Temp 1 controls Fan 1; Remote Temp 2 controls Fan 2.
01 = Remote Temp 1 controls Fan 1 and Fan 2.
10 = Remote Temp 2 controls Fan 1 and Fan 2.
11 = Max of Local Temp and Remote Temp 1 and 2 drives Fans 1 and 2.
These two bits have the following effect in software control mode.
00 = Program PWM duty cycles for Fans 1 and 2.
11 = Program RPM Speeds for Fans 1 and 2.
7
Auto/SW
Ctrl
Read/Write
Logic 1 selects automatic fan speed control; Logic 0 selects SW control. (Power-Up Default = 1)
When under software control, PWM duty cycle or RPM values can be programmed for each fan.
Table 19. Register 0×01 Configuration 2 Power-On Default = 7FH
Bit
Name
R/W
Description
0
PWM 1 En
Read/Write
Enables Fan 1 PWM output when this bit is a “1.”
1
PWM 2 En
Read/Write
Enables Fan 2 PWM output when this bit is a “1.”
2
TACH 1 En
Read/Write
Enables Tach 1 input when set to “1.”
3
TACH 2 En
Read/Write
Enables Tach 2 input when set to “1.”
4
Loc Temp En
Read/Write
Enables Interrupts on local temperature channel when set to “1.”
5
Remote 1
Temp En
Read/Write
Interrupts on Remote 1 Channel when set to “1.” Default is normally enabled, except when a diode
fault is detected on power-up.
6
Remote 2
Temp En
Read/Write
Enables Interrupts on Remote 2 Channel when set to “1.” Default is normally enabled, except when a
diode fault is detected on power-up.
7
SW Reset
Read/Write
When set to “1,” resets the device. Self-clears. Power-Up Default = 0.
Table 20. Register 0×02 Status Register 1 Power-On Default = 00H
Bit
Name
R/W
Description
0
Alarm 1 Speed
Read Only
This bit is set to “1” when fan is running at alarm speed. Once read, this bit is not reasserted on next
monitoring cycle, even if the fan is still running at alarm speed.
1
Fan 1 Fault
Read Only
This bit is set to “1” if Fan 1 becomes stuck or is running under speed.
2
Remote 1 High
Read Only
“1” indicates Remote 1 high temperature limit has been exceeded. If the temperature is still outside the
Remote 1 Temp High Limit, this bit reasserts on next monitoring cycle.
3
Remote 1 Low
Read Only
“1” indicates Remote 1 low temperature limit exceeded (below). If the temperature is still outside the
Remote 1 Temp Low Limit, this bit reasserts on next monitoring cycle.
4
Remote 1
Therm
Read Only
“1” indicates Remote 1 temperature Therm limit has been exceeded. This bit is cleared on a read of
Status Register 1.
5
Remote Diode
1 Error
Read Only
This bit is set to “1” if a short or open is detected on the Remote 1 temperature channel. This test is only
done on power-up, and if set to 1 cannot be cleared by reading the Status Register 1.
6
Local Temp
High
Read Only
This bit is set to “1” if a short or open is detected on the Remote 1 temperature channel. This test is only
done on power-up, and if set to 1 cannot be cleared by reading the Status Register 1.
7
Local Temp
Low
Read Only
“1” indicates Local Temp Low Limit has been exceeded (below). If the temperature is still outside the
Local Temp Low Limit, this bit reasserts on next monitoring cycle.
相關PDF資料
PDF描述
ADRF6604ACPZ-R7 2500 MHz - 2900 MHz RF/MICROWAVE DOUBLE BALANCED MIXER
ADRF6801ACPZ-R7 750 MHz - 1150 MHz RF/MICROWAVE I/Q DEMODULATOR
ADT14GS-REEL ANALOG TEMP SENSOR-VOLTAGE, 2.49-2.52V, 3Cel, RECTANGULAR, SURFACE MOUNT
ADT42GRT ANALOG TEMP SENSOR-VOLTAGE, 0.75V, 3Cel, RECTANGULAR, SURFACE MOUNT
ADT50GRT ANALOG TEMP SENSOR-VOLTAGE, 0.1-2V, 3Cel, RECTANGULAR, SURFACE MOUNT
相關代理商/技術參數
參數描述
ADM1031ARQ-ND 制造商:ON Semiconductor 功能描述:
ADM1031ARQ-REEL 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1031ARQ-REEL7 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1031ARQZ 功能描述:馬達/運動/點火控制器和驅動器 2 CH TDM PWM FAN CTRL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
ADM1031ARQZ-R7 功能描述:IC SENSOR 2TEMP/FAN CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*