- 您現在的位置：買賣IC網 > PDF目錄67357 > ADM1031ARQ (ON SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | ADM1031ARQ |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | MO-137AB, QSOP-16 |
| 文件頁數： | 10/35頁 |
| 文件大?。?/td> | 368K |
| 代理商： | ADM1031ARQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
ADM1031
Rev. 3 | Page 18 of 35 | www.onsemi.com
Fan Spin-Up
As mentioned in the How Does the Control Loop Work? section,
once the temperature being measured exceeds the TMIN value
programmed, the fan turns on at minimum speed (default =
33% duty cycle). However, the problem with fans being
driven by PWM is that 33% duty cycle is not enough to reliably
start the fan spinning. The solution is to spin the fan up for a
predetermined time, and once the fan has spun up, its running
speed can be reduced in line with the temperature being
measured.
The ADM1031 allows fan spin-up times between 200 ms
and 8 seconds. Bits <2:0> of Fan Characteristics Register 1
(Register 0×20) and Fan Characteristic Register 2 (Register
0×21) program the fan spin-up times.
Table 9. Fan Spin-Up Times
Bits 2:0
Spin-Up Time (Fan Characteristics Registers 1, 2)
000
200 ms
001
400 ms
010
600 ms
011
800 ms
100
1 sec
101
2 sec (Default)
110
4 sec
111
8 sec
Once the automatic fan speed control loop parameters have
been chosen, the ADM1031 device can be programmed. The
ADM1031 is placed into automatic fan speed control mode by
setting Bit 7 of Configuration Register 1 (Register 0×00). The
device powers up in automatic fan speed control mode by default.
The control mode offers further flexibility in that the user can
decide which temperature channel/channels control each fan.
Table 10. Auto Mode Fan Behavior
Bits
6, 5
Control Operation (Configuration Register 1)
00
Remote Temperature 1 Controls Fan 1
Remote Temperature 2 Controls Fan 2
01
Remote Temperature 1 Controls Fan 1 and 2
10
Remote Temperature 2 Controls Fan 1 and 2
11
Maximum Speed Calculated by Local and Remote
Temperature Channels Controls Fans 1 and 2
When Bit 5 and Bit 6 of Configuration Register 1 are both
set to 1, increased flexibility is offered. The local and remote
temperature channels can have independently programmed
control loops with different control parameters. Whichever
control loop calculates the fastest fan speed based on the
temperature being measured, drives the fans.
Figure 25 and Figure 26 show how the fan’s PWM duty cycle is
determined by two independent control loops. This is the type
of auto mode fan behavior seen when Bit 5 and Bit 6 of
Configuration Register 1 are set to 11. Figure 25 shows the
control loop for the local temperature channel. Its TMIN value
has been programmed to 20°C, and its TRANGE value is 40°C.
The local temperature’s TMAX is thus 60°C. Figure 26 shows
the control loop for the remote temperature channel. Its TMIN
value has been set to 0°C, while its TRANGE = 80°C. Therefore,
the remote temperature’s TMAX value is 80°C.
Consider if both temperature channels measure 40°C. Both
control loops calculate a PWM duty cycle of 66%. Therefore, the
fan is driven at 66% duty cycle. If both temperature channels
measure 20°C, the local channel calculates 33% PWM duty cycle,
while the Remote 1 channel calculates 50% PWM duty cycle.
Thus, the fans are driven at 50% PWM duty cycle. Consider the
local temperature measuring 60°C while the Remote 1 tempera-
ture is measuring 70°C. The PWM duty cycle calculated by the
local temperature control loop is 100% (because the temperature
= TMAX). The PWM duty cycle calculated by the Remote 1
temperature control loop at 70°C is approximately 90%.
Therefore, the fan runs full-speed (100% duty cycle). Remember,
that the fan speed is based on the fastest speed calculated, and is
not necessarily based on the highest temperature measured.
Depending on the control loop parameters programmed, a lower
temperature on one channel, can actually calculate a faster speed
than a higher temperature on the other channel.
LOCAL TEMPERATURE (°C)
PWM
DUT
Y
CYCL
E
(
%
)
0
100
93
87
80
73
66
60
53
47
40
33
TMIN
20
40
60
TMAX = TMIN + TRANGE
T R
AN
G
E
=
40
°C
02402-
025
Figure 25. Maximum Speed Calculated by Local Temperature
Control Loop Drives Fan
相關PDF資料 |
PDF描述 |
|---|---|
| ADRF6604ACPZ-R7 | 2500 MHz - 2900 MHz RF/MICROWAVE DOUBLE BALANCED MIXER |
| ADRF6801ACPZ-R7 | 750 MHz - 1150 MHz RF/MICROWAVE I/Q DEMODULATOR |
| ADT14GS-REEL | ANALOG TEMP SENSOR-VOLTAGE, 2.49-2.52V, 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADT42GRT | ANALOG TEMP SENSOR-VOLTAGE, 0.75V, 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADT50GRT | ANALOG TEMP SENSOR-VOLTAGE, 0.1-2V, 3Cel, RECTANGULAR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1031ARQ-ND | 制造商:ON Semiconductor 功能描述: |
| ADM1031ARQ-REEL | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1031ARQ-REEL7 | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1031ARQZ | 功能描述:馬達/運動/點火控制器和驅動器 2 CH TDM PWM FAN CTRL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADM1031ARQZ-R7 | 功能描述:IC SENSOR 2TEMP/FAN CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。