參數資料
型號： ADM1031ARQ
廠商： ON SEMICONDUCTOR
元件分類： 溫度/濕度傳感器
英文描述： DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
封裝： MO-137AB, QSOP-16
文件頁數： 16/35頁
文件大?。?/td> 368K
代理商： ADM1031ARQ
ADM1031
Rev. 3 | Page 23 of 35 | www.onsemi.com
As can be seen from Figure 30 through Figure 33, the rate at
which the fan reacts to temperature change is dependent on the
ramp rate selected in the fan filter register. The higher the ramp
rate, the faster the fan reaches the newly calculated fan speed.
Figure 34 shows the behavior of the PWM output as
temperature varies. As the temperature rises, the fan speed
ramps up. Small drops in temperature do not affect the ramp-up
function because the newly calculated fan speed is still higher
than the previous PWM value. The filtered mode allows the
PWM output to be made less sensitive to temperature
variations. This is dependent on the ramp rate selected and the
ADC sample rate programmed into the fan filter register.
90
PWM DUTY CYCLE
0
TIME (s)
PWM
DUT
Y
CYCL
E
(
%
)
80
70
60
30
40
50
10
20
90
0
R
TE
M
P
(°
C)
80
70
60
40
50
30
10
20
RTEMP
02402-
034
Figure 34. How Fan Reacts to Temperature Variation in Filtered Mode
Effect of ADC Sample Rate on Filtered Mode
The second way to change the filtered mode characteristics is to
adjust the ADC sample rate. The faster the ADC sample rate,
the more temperature samples are obtained per second. One
way to apply filtering to the control loop is to slow down the
ADC sampling rate. This means that the number of iterations of
the filtered mode algorithm per second is effectively reduced. If
the number of temperature measurements per second is
reduced, how often the PWM_OUT signal controlling the fan is
updated is also reduced.
Bits <4:2> of the fan filter register (Register 0×23) set the ADC
sample rate. The default ADC sample rate is 1.4 kHz. The ADC
sample rate is selectable from 87.5 Hz to 11.2 kHz. Table 13
shows how many temperature samples are obtained per second,
for each of the ADC sample rates.
Table 13. Temperature Updates per Second
ADC Sample Rate
Temperature Updates/Sec
87.5 Hz
0.0625
175 Hz
0.125
350 Hz
0.25
700 kHz
0.5
1.4 kHz
1 (Default)
2.8 kHz
2
5.6 kHz
4
11.2 kHz
8
Relevant Registers for Filtered Automatic Fan Speed
Control Mode
In addition to the registers used to program the normal
automatic fan speed control mode, the following register needs
to be programmed.
Register 0×23 Fan Filter Register
<7> Spin-up Disable: When this bit is set to 1, fan spin-up is
disabled. (Default = 0)
<6:5> Ramp Rate: These bits set the ramp rate for filtered mode.
00 = 1 (0.416% Duty Cycle Change)
01 = 2 (0.833% Duty Cycle Change)
10 = 4 (1.66% Duty Cycle Change)
11 = 8 (3.33% Duty Cycle Change)
<4:2> ADC Sample Rate.
000 = 87.5 Hz
001 = 175 Hz
010 = 350 Hz
011 = 700 Hz
100 = 1.4 kHz (Default)
101 = 2.8 kHz
110 = 5.6 kHz
111 = 11.2 kHz
<1> Fan 2 Filter Enable: When this bit is set to 1, it enables
filtering on Fan 2. Default = 0.
<0> Fan 1 Filter Enable: When this bit is set to 1, it enables
filtering on Fan 1. Default = 0.
Programming the Filtered Automatic Fan Speed Control
Loop
1.
Program a value for TMIN.
2.
Program a value for the slope TRANGE.
3.
TMAX = TMIN + TRANGE.
4.
Program a value for fan spin-up time.
5.
Program the desired automatic fan speed control mode
behavior, that is, which temperature channel controls the
fan.
6.
Program a ramp rate for the filtered mode.
7.
Program the ADC sample rate in the fan filter register.
8.
Set Bit 0 to enable fan filtered mode for Fan 1.
9.
Set Bit 1 to enable the fan filtered mode for Fan 2.
10. Select automatic fan speed control mode by setting Bit 7 of
Configuration Register 1.
相關PDF資料
PDF描述
ADRF6604ACPZ-R7 2500 MHz - 2900 MHz RF/MICROWAVE DOUBLE BALANCED MIXER
ADRF6801ACPZ-R7 750 MHz - 1150 MHz RF/MICROWAVE I/Q DEMODULATOR
ADT14GS-REEL ANALOG TEMP SENSOR-VOLTAGE, 2.49-2.52V, 3Cel, RECTANGULAR, SURFACE MOUNT
ADT42GRT ANALOG TEMP SENSOR-VOLTAGE, 0.75V, 3Cel, RECTANGULAR, SURFACE MOUNT
ADT50GRT ANALOG TEMP SENSOR-VOLTAGE, 0.1-2V, 3Cel, RECTANGULAR, SURFACE MOUNT
相關代理商/技術參數
參數描述
ADM1031ARQ-ND 制造商:ON Semiconductor 功能描述:
ADM1031ARQ-REEL 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1031ARQ-REEL7 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1031ARQZ 功能描述:馬達/運動/點火控制器和驅動器 2 CH TDM PWM FAN CTRL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
ADM1031ARQZ-R7 功能描述:IC SENSOR 2TEMP/FAN CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*