- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADM1030ARQZ-RL7 (ON Semiconductor)IC SNSR TEMP/FAN PWM CTRL 16QSOP Datasheet資料下載
參數資料
| 型號： | ADM1030ARQZ-RL7 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 23/30頁 |
| 文件大?。?/td> | 327K |
| 描述： | IC SNSR TEMP/FAN PWM CTRL 16QSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi Product Obsolescence 11/Feb/2009 |
| 標準包裝： | 1,000 |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | 0°C ~ 100°C，外部傳感器 |
| 精確度： | ±1°C，±1°C（最小值） |
| 拓?fù)洌?/td> | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 100°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
ADM1030
http://onsemi.com
23
signal. Setting Bit 3 of Configuration Register 1 (0x00) to 1,
inverts the PWM_OUT signal. This makes the PWM_OUT
pin high for 100% duty cycle. Bit 3 of Configuration
Register 1 should generally be set to 1, when using an
n-MOS device to drive the fan. If using a p-MOS device,
Bit 3 of Configuration Register 1 should be cleared to 0.
Fan Fault
s
The FAN_FAULT
output (Pin 8) is an active-low,
open-drain output used to signal fan failure to the system
processor. Writing a Logic 1 to Bit 4 of Configuration
Register 1 (0x00) enables the FAN_FAULT
output pin. The
FAN_FAULT
output is enabled by default. The
FAN_FAULT
output asserts low only when five consecutive
interrupts are generated by the ADM1030 device due to the
fan running underspeed, or if the fan is completely stalled.
Note that the Fan Tach High Limit must be exceeded by at
least one before a FAN_FAULT
can be generated. For
example, if we are only interested in getting a FAN_FAULT
if the fan stalls, then the fan speed value will be 0xFF for a
failed fan. Therefore, we should make the Fan Tach High
Limit = 0xFE to allow FAN_FAULT
to be asserted after five
consecutive fan tach failures.
Figure 38 shows the relationship between INT
,
FAN_FAULT
, and the PWM drive channel. The
PWM_OUT channel is driving a fan at some PWM duty
cycle, say 50%, and the fans tach signal (or fan current for
a 2-wire fan) is being monitored at the TACH/AIN pin. Tach
pulses are being generated by the fan, during the high time
of the PWM duty cycle train. The tach is pulled high during
the off time of the PWM train because the fan is connected
high-side to the n-MOS device.
Suppose the fan has already failed its fan speed
measurement twice previously. Looking at Figure 38,
PWM_OUT is brought high for two seconds, to restart the
fan if it has stalled. Sometime later a third tach failure
occurs. This is evident by the tach signal being low during
the high time of the PWM pulse, causing the Fan Speed
Reading register to reach its maximum count of 255. Since
the tach limit has been exceeded, an interrupt is generated on
the INT
pin. The Fan Fault bit (Bit 1) of Interrupt Status
Register 1 (Register 0x02) will also be asserted. Once the
processor has acknowledged the INT
by reading the status
register, the INT
is cleared. PWM_OUT is then brought high
for another 2 seconds to restart the fan. Subsequent fan
failures cause INT
to be reasserted and the PWM_OUT
signal is brought high for 2 seconds (fan spin-up default)
each time to restart the fan. Once the fifth tach failure occurs,
the failure is deemed to be catastrophic, and the
FAN_FAULT
pin is asserted low. PWM_OUT is brought
high to attempt to restart the fan. The INT
pin will continue
to generate interrupts after the assertion of FAN_FAULT
since tach measurement continues even after fan failure.
Should the fan recover from its failure condition, the
FAN_FAULT
signal will be negated, and the fan will return
to its normal operating speed.
Figure 39 shows a typical application circuit for the
ADM1030. Temperature monitoring can be based around a
CPU diode or discrete transistor measuring thermal
hotspots. Either 2- or 3-wire fans may be monitored by the
ADM1030, as shown.
Figure 38. Operation of FAN_FAULT
and Interrupt Pins
PWM_OUT
TACH/AIN
INT
FAN_FAULT
STATUS REG READ TO
CLEAR INTERRUPT
FULL SPEED
2 SECS
2 SECS
2 SECS
3RD TACH
FAILURE
4TH TACH
FAILURE
5TH TACH
FAILURE
CONTINUING
TACH FAILURE
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1032ARZ-REEL | IC TEMP MONITOR 85DEG 8SOIC |
| ADM1033ARQZ-RL7 | IC THERM/FAN SPEED CTLR 16-QSOP |
| ADM1034ARQZ-REEL | IC THERM/FAN SPEED CTRLR 16-QSOP |
| ADN8810ACPZ-REEL7 | IC CURRENT SOURCE(12BIT) 24LFCSP |
| ADP2140ACPZ3328R7 | IC REG DL BCK/LINEAR 10LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1031 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Intelligent Temperature Monitor and Dual PWM Fan Controller |
| ADM1031ARQ | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1031ARQ-ND | 制造商:ON Semiconductor 功能描述: |
| ADM1031ARQ-REEL | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1031ARQ-REEL7 | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。