參數資料
型號： ADM1030ARQ-REEL7
廠商： ANALOG DEVICES INC
元件分類： 溫度/濕度傳感器
英文描述： DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT
封裝： MO-137AB, QSOP-16
文件頁數： 28/28頁
文件大小： 495K
代理商： ADM1030ARQ-REEL7
REV. A
ADM1030
–9–
ALERT RESPONSE ADDRESS
Alert Response Address (ARA) is a feature of SMBus devices
that allows an interrupting device to identify itself to the host
when multiple devices exist on the same bus.
The
INT output can be used as an interrupt output or can be used
as an
SMBALERT. One or more INT outputs can be connected
to a common
SMBALERT line connected to the master. If a
device’s
INT line goes low, the following procedure occurs:
1.
SMBALERT pulled low.
2. Master initiates a read operation and sends the Alert
Response Address (ARA = 0001 100). This is a general call
address that must not be used as a specific device address.
3. The device whose
INT output is low responds to the Alert
Response Address, and the master reads its device address.
The address of the device is now known and can be interro-
gated in the usual way.
4. If more than one device’s
INT output is low, the one with
the lowest device address will have priority, in accordance
with normal SMBus arbitration.
5. Once the ADM1030 has responded to the Alert Response
Address, it will reset its
INT output; however, if the error
condition that caused the interrupt persists,
INT will be
reasserted on the next monitoring cycle.
TEMPERATURE MEASUREMENT SYSTEM
Internal Temperature Measurement
The ADM1030 contains an on-chip bandgap temperature sen-
sor. The on-chip ADC performs conversions on the output of
this sensor and outputs the temperature data in 10-bit two’s
complement format. The resolution of the local temperature
sensor is 0.25
∞C. The format of the temperature data is shown
in Table II.
External Temperature Measurement
The ADM1030 can measure the temperature of an external
diode sensor or diode-connected transistor, connected to Pins
9 and 10.
These pins are a dedicated temperature input channel. The
function of Pin 7 is as a
THERM input/output and is used to
flag overtemperature conditions.
The forward voltage of a diode or diode-connected transistor,
operated at a constant current, exhibits a negative temperature
coefficient of about –2 mV/
∞C. Unfortunately, the absolute
value of VBE, varies from device to device, and individual
calibration is required to null this out, so the technique is
unsuitable for mass production.
The technique used in the ADM1030 is to measure the change
in VBE when the device is operated at two different currents.
This is given by:
DVBE = KT/q ln (N)
where:
K is Boltzmann’s constant.
q is charge on the carrier.
T is absolute temperature in Kelvins.
N is ratio of the two currents.
Figure 3 shows the input signal conditioning used to measure
the output of an external temperature sensor. This figure shows
the external sensor as a substrate transistor, provided for tempera-
ture monitoring on some microprocessors, but it could equally
well be a discrete transistor.
LOW-PASS
FILTER
fC = 65kHz
BIAS
DIODE
REMOTE
SENSING
TRANSISTOR
IN
IIBIAS
D+
D–
VOUT+
VOUT–
TO
ADC
VDD
Figure 3. Signal Conditioning
If a discrete transistor is used, the collector will not be grounded,
and should be linked to the base. If a PNP transistor is used, the
base is connected to the D– input and the emitter to the D+
input. If an NPN transistor is used, the emitter is connected to
the D– input and the base to the D+ input.
One LSB of the ADC corresponds to 0.125
∞C, so the ADM1030
can theoretically measure temperatures from –127
∞C to +127.75∞C,
although –127
∞C is outside the operating range for the device.
The extended temperature resolution data format is shown in
Tables III and IV.
Table II. Temperature Data Format (Local Temperature and
Remote Temperature High Bytes)
Temperature ( C)
Digital Output
–128
∞C
1000 0000
–125
∞C
1000 0011
–100
∞C
1001 1100
–75
∞C
1011 0101
–50
∞C
1100 1110
–25
∞C
1110 0111
–1
∞C
1111 1111
0
∞C
0000 0000
+1
∞C
0000 0001
+10
∞C
0000 1010
+25
∞C
0001 1001
+50
∞C
0011 0010
+75
∞C
0100 1011
+100
∞C
0110 0100
+125
∞C
0111 1101
+127
∞C
0111 1111
相關PDF資料
PDF描述
ADM1030ARQZ-REEL7 DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT
ADM1030ARQZ DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT
ADM1030ARQ DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT
ADM1031ARQZ-R7 DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
ADM1031ARQZ-REEL DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
相關代理商/技術參數
參數描述
ADM1030ARQZ 功能描述:馬達/運動/點火控制器和驅動器 TDM & PWM FAN CNTRLRS IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
ADM1030ARQZ-REEL 功能描述:板上安裝溫度傳感器 TDM PWM FAN CTRLRS IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADM1030ARQZ-REEL7 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1030ARQZ-RL7 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1031 制造商:AD 制造商全稱:Analog Devices 功能描述:Intelligent Temperature Monitor and Dual PWM Fan Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*