- 您現在的位置：買賣IC網 > PDF目錄378285 > ADC14061 (National Semiconductor Corporation) Low Dropout Linear 2-cell Li-Ion Charge Controller with AutoCompTM, 8.4V 8-SOIC -20 to 70 PDF資料下載
參數資料
| 型號： | ADC14061 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Low Dropout Linear 2-cell Li-Ion Charge Controller with AutoCompTM, 8.4V 8-SOIC -20 to 70 |
| 中文描述： | 自校準14位，250 MSPS的，390毫瓦的A / D轉換器 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 471K |
| 代理商： | ADC14061 |
Specification Definitions
APERTURE JITTER
is the variation in aperture delay from
sample to sample. Aperture jitter shows up as input noise.
APERTURE DELAY
is the time required after the falling
edge of the clock for the sampling switch to open. In other
words, for the Track/Hold circuit to go from
″
track
″
mode into
the
″
hold
″
mode. The Track/Hold circuit effectively stops
capturing the input signal and goes into the
″
hold
″
mode t
AD
after the fall of the clock.
OFFSET ERROR
is the difference between the ideal LSB
transition to the actual transition point. The LSB transition
should occur when V
IN
+ = V
IN
.
DIFFERENTIAL NON-LINEARITY (DNL)
is the measure of
the maximum deviation from the ideal step size of 1 LSB.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE
BITS)
is another method of specifying Signal-to-Noise and
Distortion Ratio, or SINAD. ENOB is defined as (SINAD
1.76) / 6.02.
FULL SCALE ERROR
is the difference between the input
voltage [(V
+) (V
IN
)] just causing a transition to positive
full scale and V
REF
1.5 LSB, where V
REF
is ( V
REF
+
IN
)
(V
REF
IN
).
FULL POWER BANDWIDTH
is a measure of the frequency
at which the reconstructed output fundamental drops 3 dB
below its low frequency value for a full scale input. The test
is performed with f
IN
equal to 100 kHz plus integral multiples
of f
CLK
. The input frequency at which the output is 3 dB
relative to the low frequency input signal is the full power
bandwidth.
INTERMODULATION DISTORTION (IMD)
is the creation of
additional spectral components as a result of two sinusoidal
frequencies being applied to theADC input at the same time.
Timing Diagrams
It is defined as the ratio of the power in the intermodulation
products to the total power in the original frequencies. IMD is
usually expressed in dB.
INTEGRAL NON-LINEARITY (INL)
is a measure of the de-
viation of each individual code from a line drawn from nega-
tive full scale (
1
2
LSB below the first code transition) through
positive full scale (the last code transition). The deviation of
any given code from this straight line is measured from the
center of that code value.
PIPELINE DELAY (LATENCY)
is the number of clock cycles
between initiation of conversion and when that data is pre-
sented to the output stage. Data for any given sample is
available the Pipeline Delay plus the Output Delay after that
sample is taken. New data is available at every clock cycle,
but the data lags the conversion by the pipeline delay.
SIGNAL TO NOISE RATIO (SNR)
is the ratio, expressed in
dB, of the rms value of the input signal to the rms value of the
sum of all other spectral components below one-half the
sampling frequency, not including harmonics or dc.
SIGNAL TO NOISE PLUS DISTORTION (S/(N+D) or SI-
NAD)
) Is the ratio, expressed in dB, of the rms value of the
input signal to the rms value of all of the other spectral com-
ponents below half the clock frequency, including harmonics
but excluding dc.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
is the differ-
ence, expressed in dB, between the rms values of the input
signal and the peak spurious signal, where a spurious signal
is any signal present in the output spectrum that is not
present at the input.
TOTAL HARMONIC DISTORTION (THD)
is the ratio, ex-
pressed in dB or dBc, of the rms total of the first six harmonic
components, to the rms value of the input signal.
DS100103-15
TIMING DIAGRAM 1. Output Timing
A
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| ADC14071CIVBH | 14-Bit, 7 MSPS, 380 mW A/D Converter |
| ADC14071 | 14-Bit, 7 MSPS, 380 mW A/D Converter |
| ADC14071EVAL | 14-Bit, 7 MSPS, 380 mW A/D Converter |
| ADC14161 | Low Dropout Linear 2-cell Li-Ion Charge Controller with AutoCompTM, 8.4V 8-SOIC -20 to 70 |
| ADC14161CIVT | Low-Distortion, Self-Calibrating 14-Bit, 2.5 MSPS, 390 mW A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC14061EVAL | 功能描述:BOARD EVALUATION FOR ADC14061 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| ADC14071A WAF | 制造商:Texas Instruments 功能描述: |
| ADC1410S065/DB,598 | 功能描述:數據轉換 IC 開發工具 ADC DEMO BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| ADC1410S065F1-DB | 功能描述:ADC1410S065 - 14 Bit 65M Samples per Second Analog to Digital Converter (ADC) Evaluation Board 制造商:idt, integrated device technology inc 系列:- 零件狀態:過期 A/D 轉換器數:1 位數:14 采樣率（每秒）:65M 數據接口:SPI 輸入范圍:2 Vpp 不同條件下的功率（典型值）:380mW @ 65MSPS 使用的 IC/零件:ADC1410S065 所含物品:板 標準包裝:1 |
| ADC1410S065F2-DB | 功能描述:ADC1410S065 - 14 Bit 65M Samples per Second Analog to Digital Converter (ADC) Evaluation Board 制造商:idt, integrated device technology inc 系列:- 零件狀態:過期 A/D 轉換器數:1 位數:14 采樣率（每秒）:65M 數據接口:SPI 輸入范圍:2 Vpp 不同條件下的功率（典型值）:380mW @ 65MSPS 使用的 IC/零件:ADC1410S065 所含物品:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。