參數資料
型號： ADC12041CIV
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： ADC
英文描述： 12-Bit Plus Sign 216 kHz Sampling Analog-to-Digital Converter
中文描述： 1-CH 13-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC28
封裝： PLASTIC, LCC-28
文件頁數： 24/28頁
文件大?。?/td> 591K
代理商： ADC12041CIV
Analog Application Information
(Continued)
Part Number
Output Voltage
Tolerance
±
0.5%
±
0.1%
±
0.2%
±
0.1%
±
0.5%
Adjustable
Temperature
Coefficient
±
100ppm/C
±
100ppm/C
±
50ppm/C
±
50ppm/C
±
25ppm/C
±
2ppm/C
LM4041CI-Adj
LM4040AI-4.1
LM4050
LM4120
LM9140BYZ-4.1
Circuit of Figure 20
INPUT CURRENT
At the start of the acquisition window (t
) a charg-
ing current (due to capacitive switching) flows through the
analog input pins (ADCIN+ and ADCIN). The peak value of
this input current will depend on the amplitude and frequency
of the input voltage applied, the source impedance and the
ADCIN+ and ADCIN input switch ON resistance of 2500
.
For low impedance voltage sources (
<
1000
for 12 MHz
operation), the input charging current will decay to a value
that will not introduce any conversion errors before the end
of the default sample-and-hold (S/H) acquisition time
(9 clock cycles). For higher source impedances (
>
1000
for 12 MHz operation), the S/H acquisition time should be in-
creased to allow the charging current to settle within speci-
fied limits. In asynchronous mode, the acquisition time may
be increased to 15, 47 or 79 clock cycles. If different acqui-
sition times are needed, the synchronous mode can be used
to fully control the acquisition time.
INPUT BYPASS CAPACITANCE
External capacitors (0.01 μF–0.1 μF) can be connected be-
tween the ADCIN+ and ADCIN analog input pins and the
analog ground to filter any noise caused by inductive pickup
associated with long leads.
POWER SUPPLY CONSIDERATIONS
Decoupling and bypassing the power supply on a high reso-
lution ADC is an important design task. Noise spikes on the
V
+ (analog supply) or V
+ (digital supply) can cause con-
version errors. The analog comparator used in the ADC will
respond to power supply noise and will make erroneous con-
version decisions. The ADC is especially sensitive to power
supply spikes that occur during the auto-zero or linearity cali-
bration cycles.
The ADC12041 is designed to operate from a single +5V
power supply. The separate supply and ground pins for the
analog and digital portions of the circuit allow separate exter-
nal bypassing. To minimize power supply noise and ripple,
adequate bypass capacitors should be placed directly be-
tween power supply pins and their associated grounds. Both
supply pins should be connected to the same supply source.
In systems with separate analog and digital supplies, the
ADC should be powered from the analog supply. At least a
10 μF tantalum electrolytic capacitor in parallel with a 0.1 μF
monolithic ceramic capacitor is recommended for bypassing
each power supply. The key consideration for these capaci-
tors is to have low series resistance and inductance. The ca-
pacitors should be placed as close as physically possible to
the supply and ground pins with the smaller capacitor closer
to the device. The capacitors also should have the shortest
possible leads in order to minimize series lead inductance.
Surface mount chip capacitors are optimal in this respect
and should be used when possible.
When the power supply regulator is not local on the board,
adequate bypassing (a high value electrolytic capacitor)
should be placed at the power entry point. The value of the
capacitor depends on the total supply current of the circuits
on the PC board. All supply currents should be supplied by
the capacitor instead of being drawn from the external sup-
ply lines, while the external supply charges the capacitor at a
steady rate.
TheADC has two V
+ and DGND pins. It is recommended to
use a 0.1 μF plus a 10 μF capacitor between pin 21(V
D
+)
DS012441-44
*Tantalum
*
*Ceramic
FIGURE 20. Low Drift Extremely Stable Reference Circuit
A
www.national.com
24
相關PDF資料
PDF描述
ADC12041CIMSA NiCd/NiMH/Lead-Acid Gas Gauge For High Discharge Rates (&gt;10A), Pgmable Offset Error &amp; Load Comp. 16-SOIC 0 to 70
ADC12048EVAL 12-Bit Plus Sign 216 kHz 8-Channel Sampling Analog-to-Digital Converter
ADC12048CIVF 12-Bit Plus Sign 216 kHz 8-Channel Sampling Analog-to-Digital Converter
ADC12048 12-Bit Plus Sign 216 kHz 8-Channel Sampling Analog-to-Digital Converter
ADC12048CIV 12-Bit Plus Sign 216 kHz 8-Channel Sampling Analog-to-Digital Converter
相關代理商/技術參數
參數描述
ADC12041CIVX 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit Plus Sign 216 kHz Sampling Analog-to-Digital Converter
ADC12048 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit Plus Sign 216 kHz 8-Channel Sampling Analog-to-Digital Converter
ADC12048_02 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit Plus Sign 216kHz 8-Channel Sampling Analog-to-Digital Converter
ADC12048CIV 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADC12048CIV/NOPB 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*