- 您現在的位置：買賣IC網 > PDF目錄378281 > ADC10321 (National Semiconductor Corporation) 10-Bit, 20MSPS, 98mW A/D Converter with Internal Sample and Hold(10位20MSPS, 98 mW帶內部采樣和保持功能A/D轉換器) PDF資料下載
參數資料
| 型號： | ADC10321 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 10-Bit, 20MSPS, 98mW A/D Converter with Internal Sample and Hold(10位20MSPS, 98 mW帶內部采樣和保持功能A/D轉換器) |
| 中文描述： | 10位，20MSPS，98mW的A / D轉換器內部采樣和保持（10位20MSPS，98毫瓦帶內部采樣和保持功能的A / D轉換器） |
| 文件頁數： | 9/16頁 |
| 文件大小： | 395K |
| 代理商： | ADC10321 |
Typical Performance Characteristics
V
A
= V
D
= V
D
I/O = 5V, f
CLK
= 20MHz, unless otherwise
specified. (Continued)
Specification Definitions
APERTURE JITTER
is the variation in aperture delay from
sample to sample. Aperture jitter shows up as input noise.
APERTURE DELAY
See Sampling Delay.
DIFFERENTIAL GAIN ERROR
is the percentage difference
between the output amplitudes of a given amplitude small
signal, high frequency sine wave input at two different dc
input levels.
DIFFERENTIAL PHASE ERROR
is the difference in the
output phase of a small signal sine wave input at two differ-
ent dc input levels.
DIFFERENTIAL NON-LINEARITY (DNL)
is the measure of
the maximum deviation from the ideal step size of 1 LSB.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE
BITS)
is another method of specifying Signal-to-Noise and
Distortion Ratio (S/N+D or SINAD). ENOB is defined as
(SINAD 1.76) / 6.02.
FULL POWER BANDWIDTH
is a measure of the frequency
at which the reconstructed output fundamental drops 3 dB
below its 1MHz value for a full scale input. The test is
performed with f
IN
equal to 100 kHz plus integral multiples of
f
CLK
. The input frequency at which the output is 3 dB
relative to the1MHz input signal is the full power bandwidth.
FULL SCALE (FS) INPUT RANGE
of the ADC is the input
range of voltages over which the ADC will digitize that input.
For V
+ = 3.50V and V
REF
= 1.50V, FS = (V
REF
+)
(V
REF
) = 2.00V.
FULL SCALE OFFSET ERROR
is a measure of how far the
last code transition is from the ideal 1
1
2
LSB below V
REF
+
and is defined as V
1.5 LSB V
+ , where V
is
the voltage at which the transitions from code 1022 to 1023
occurs.
FULL SCALE STEP RESPONSE
is defined as the time
required after V
goes from V
to V
+, or V
+ to
V
, and settles sufficiently for the converter to recover
and make a conversion with its rated accuracy.
INTEGRAL NON-LINEARITY (INL)
is a measure of the
deviation of each individual code from a line drawn from
negative full scale (
1
2
LSB below the first code transition)
through positive full scale (1
1
2
LSB above the last code
transition). The deviation of any given code from this straight
line is measured from the center of that code value.
OUTPUT DELAY
is the time delay after the fall of the input
clock before the data update is present at the output pins.
OUTPUT HOLD TIME
is the length of time that the output
data is valid after the fall of the input clock.
OVER RANGE RECOVERY TIME
is the time required after
V
goes from AGND to V
+ or V
goes from V
to V
for the converter to recover and make a conversion with its
rated accuracy.
PIPELINE DELAY (LATENCY)
is the number of clock cycles
between initiation of conversion and when that data is pre-
sented to the output driver stage. Data for any given sample
is available by the Pipeline Delay plus the Output Delay after
that sample is taken. New data is available at every clock
cycle, but the data lags the conversion by the pipeline delay.
PSRR (POWER SUPPLY REJECTION RATIO)
is the ratio
of the change in dc power supply voltage to the resulting
change in Full Scale Error, expressed in dB.
SAMPLING (APERTURE) DELAY or APERTURE TIME
is
that time required after the fall of the clock input for the
sampling switch to open. The sample is effectively taken this
amount of time after the fall of the clock input.
SIGNAL TO NOISE RATIO (SNR)
is the ratio, expressed in
dB, of the rms value of the input signal to the rms value of the
sum of all other spectral components below one-half the
sampling frequency, not including harmonics or dc.
SIGNAL TO NOISE PLUS DISTORTION (S/(N+D) or SI-
NAD)
is the ratio, expressed in dB, of the RMS value of the
input signal to the RMS value of all of the other spectral
components below half the clock frequency, including har-
monics but excluding dc.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
is the differ-
ence, expressed in dB or dBc, between the RMS values of
the input signal and the peak spurious signal, where a
spurious signal is any signal present in the output spectrum
that is not present at the input.
TOTAL HARMONIC DISTORTION (THD)
is the ratio, ex-
pressed in dB, of the rms total of the first six harmonic
components, to the rms value of the input signal.
ZERO SCALE OFFSET ERROR
is the difference between
the ideal input voltage (
1
2
LSB) and the actual input voltage
that just causes a transition from an output code of zero to
an output code of one.
Spectral Response at 20 MSPs
DS100897-35
A
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| ADC1038CIWM | 10-Bit Serial I/O A/D Converter with Analog Multiplexer |
| ADC1038 | 10-Bit Serial I/O A/D Converter with Analog Multiplexer |
| ADC10461 | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
| ADC10461CIWM | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
| ADC10462CIWM | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC10321CIVT | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC10321CIVT/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC10321EVAL | 功能描述:BOARD EVALUATION FOR ADC10321 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADC1034 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:ADC1031/ADC1034/ADC1038 10-Bit Serial I/O A/D Converters with Analog Multiplexer and Track/Hold Function |
| ADC1034BIJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit |
發布緊急采購，3分鐘左右您將得到回復。