- 您現在的位置：買賣IC網 > PDF目錄1988 > AD9644BCPZ-80 (Analog Devices Inc)IC ADC 14BIT 80MSPS 3V 48LFCSP PDF資料下載
參數資料
| 型號： | AD9644BCPZ-80 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT 80MSPS 3V 48LFCSP |
| 標準包裝： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 80M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 460mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP-VQ（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 2 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9644
Data Sheet
Rev. C | Page 20 of 44
THEORY OF OPERATION
The AD9644 dual-core analog-to-digital converter (ADC) can
be used for diversity reception of signals, in which the ADCs are
operating identically on the same carrier but from two separate
antennae. The ADCs can also be operated with independent
analog inputs. The user can sample any fS/2 frequency segment
from dc to 250 MHz, using appropriate low-pass or band-pass
filtering at the ADC inputs with little loss in ADC performance.
In nondiversity applications, the AD9644 can be used as a base-
band or direct downconversion receiver, in which one ADC is
used for I input data, and the other is used for Q input data.
Synchronization capability is provided to allow synchronized
timing between multiple devices.
Programming and control of the AD9644 are accomplished
using a 3-wire SPI-compatible serial interface.
ADC ARCHITECTURE
The AD9644 architecture consists of a dual front-end sample-
and-hold circuit, followed by a pipelined, switched-capacitor
ADC. The quantized outputs from each stage are combined into
a final 14-bit result in the digital correction logic. The pipelined
architecture permits the first stage to operate on a new input
sample and the remaining stages to operate on the preceding
samples. Sampling occurs on the rising edge of the clock.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched-capacitor digital-
to-analog converter (DAC) and an interstage residue amplifier
(MDAC). The MDAC magnifies the difference between the recon-
structed DAC output and the flash input for the next stage in
the pipeline. One bit of redundancy is used in each stage to
facilitate digital correction of flash errors. The last stage simply
consists of a flash ADC.
The input stage of each channel contains a differential sampling
circuit that can be ac- or dc-coupled in differential or single-
ended modes. The output staging block aligns the data, corrects
errors, and passes the data to the output buffers. The output buffers
are powered from a separate supply, allowing digital output noise to
be separated from the analog core. During power-down, the
output buffers go into a high impedance state.
ANALOG INPUT CONSIDERATIONS
The analog input to the AD9644 is a differential switched-
capacitor circuit that has been designed for optimum performance
while processing a differential input signal.
The clock signal alternatively switches the input between sample
mode and hold mode (see Figure 48). When the input is switched
into sample mode, the signal source must be capable of charging
the sample capacitors and settling within of a clock cycle.
A small resistor in series with each input can help reduce the
peak transient current required from the output stage of the
driving source. A shunt capacitor can be placed across the
inputs to provide dynamic charging currents. This passive
network creates a low-pass filter at the ADC input; therefore,
the precise values are dependent on the application.
In intermediate frequency (IF) undersampling applications, any
shunt capacitors or series resistors should be reduced since the
input sample capacitor is unbuffered. In combination with the
driving source impedance, the shunt capacitors limit the input
bandwidth. Refer to the AN-742 Application Note, Frequency
Domain Response of Switched-Capacitor ADCs; the AN-827
Application Note, A Resonant Approach to Interfacing Amplifiers to
Switched-Capacitor ADCs; and the Analog Dialog article,
for more information on this subject (refer to www.analog.com).
CPAR1
CPAR2
S
CFB
CS
BIAS
VIN+
H
VIN–
09180-
034
Figure 48. Switched-Capacitor Input
For best dynamic performance, the source impedances driving
VIN+ and VIN should be matched, and the inputs should be
differentially balanced.
Input Common Mode
The analog inputs of the AD9644 are not internally dc biased.
In ac-coupled applications, the user must provide this bias
externally. Setting the device so that VCM = 0.5 × AVDD (or
0.9 V) is recommended for optimum performance. An on-
board common-mode voltage reference is included in the
design and is available from the VCMA and VCMB pins. Using
the VCMA and VCMB outputs to set the input common mode
is recommended. Optimum performance is achieved when the
common-mode voltage of the analog input is set by the VCMA
and VCMB pin voltages (typically 0.5 × AVDD). The VCMA
and VCMB pins must be decoupled to ground by a 0.1 F
capacitor. This decoupling capacitor should be placed close
to the pin to minimize the series resistance and inductance
between the part and this capacitor.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9648BCPZRL7-125 | IC ADC 14BIT 125MSPS 64LFCSP |
| AD9649BCPZRL7-80 | IC ADC 14BIT 80MSPS 32LFCSP |
| AD9653BCPZRL7-125 | IC ADC 16BIT 125MSPS SRL 48LFCSP |
| AD9707BCPZRL7 | IC DAC TX 14BIT 175MSPS 32-LFCSP |
| AD9709ASTZRL | IC DAC 8BIT DUAL 125MSPS 48LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9644BCPZRL7-155 | 功能描述:模數轉換器 - ADC 14 Bit 155 Msps Dual 1.8V ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9644BCPZRL7-80 | 功能描述:IC ADC 14BIT 80MSPS 3V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9644CCPZ-80 | 功能描述:IC ADC 14BIT 80MSPS 3V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9644CCPZRL7-80 | 功能描述:IC ADC 14BIT 80MSPS 3V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9645 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual, 14-Bit, 80 MSPS/125 MSPS, Serial LVDS |
發布緊急采購，3分鐘左右您將得到回復。