- 您現在的位置：買賣IC網 > PDF目錄1988 > AD9627ABCPZ11-150 (Analog Devices Inc)IC ADC 11BIT 150MSPS 64LFCSP PDF資料下載
參數資料
| 型號： | AD9627ABCPZ11-150 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 11BIT 150MSPS 64LFCSP |
| 標準包裝： | 1 |
| 位數： | 11 |
| 采樣率（每秒）： | 150M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 890mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 4 個單端，單極；2 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
AD9627-11
Rev. B | Page 23 of 72
THEORY OF OPERATION
The AD9627-11 dual ADC design can be used for diversity recep-
tion of signals, where the ADCs are operating identically on the
same carrier but from two separate antennae. The ADCs can also
be operated with independent analog inputs. The user can sample
any fS/2 frequency segment from dc to 200 MHz, using appropriate
low-pass or band-pass filtering at the ADC inputs with little loss
in ADC performance. Operation to 450 MHz analog input is
permitted but occurs at the expense of increased ADC noise and
distortion.
In nondiversity applications, the AD9627-11 can be used as a base-
band or direct downconversion receiver, where one ADC is
used for I input data and the other is used for Q input data.
Synchronization capability is provided to allow synchronized
timing between multiple channels or multiple devices.
Programming and control of the AD9627-11 are accomplished
using a 3-bit SPI-compatible serial interface.
ADC ARCHITECTURE
The AD9627-11 architecture consists of a dual front-end sample-
and-hold amplifier (SHA), followed by a pipelined, switched-
capacitor ADC. The quantized outputs from each stage are
combined into a final 11-bit result in the digital correction logic.
The pipelined architecture permits the first stage to operate on
a new input sample and the remaining stages to operate on the
preceding samples. Sampling occurs on the rising edge of the clock.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched-capacitor digital-
to-analog converter (DAC) and an interstage residue amplifier
(MDAC). The residue amplifier magnifies the difference between
the reconstructed DAC output and the flash input for the next
stage in the pipeline. One bit of redundancy is used in each stage
to facilitate digital correction of flash errors. The last stage
simply consists of a flash ADC.
The input stage of each channel contains a differential SHA that
can be ac- or dc-coupled in differential or single-ended modes.
The output staging block aligns the data, corrects errors, and passes
the data to the output buffers. The output buffers are powered from
a separate supply, allowing adjustment of the output voltage swing.
During power-down, the output buffers go into a high impedance
state.
ANALOG INPUT CONSIDERATIONS
The analog input to the AD9627-11 is a differential switched-
capacitor SHA that has been designed for optimum performance
while processing a differential input signal.
The clock signal alternatively switches the SHA between sample
mode and hold mode (see Figure 45). When the SHA is switched
into sample mode, the signal source must be capable of charging
the sample capacitors and settling within 1/2 of a clock cycle.
A small resistor in series with each input can help reduce the
peak transient current required from the output stage of the
driving source. A shunt capacitor can be placed across the
inputs to provide dynamic charging currents. This passive
network creates a low-pass filter at the ADC input; therefore,
the precise values are dependent on the application.
In intermediate frequency (IF) undersampling applications,
any shunt capacitors should be reduced. In combination with
the driving source impedance, the shunt capacitors limit the
input bandwidth. See Application Note AN-742, Frequency
Domain Response of Switched-Capacitor ADCs; Application
Note AN-827, A Resonant Approach to Interfacing Amplifiers
to Switched-Capacitor ADCs; and the Analog Dialogue article,
“Transformer-Coupled Front-End for Wideband A/D Converters,”
for more information on this subject.
VIN+
VIN–
CPIN, PAR
CS
CH
H
S
07
05
4-
04
5
Figure 45. Switched-Capacitor SHA Input
For best dynamic performance, the source impedances driving
VIN+ and VIN should be matched.
An internal differential reference buffer creates positive and
negative reference voltages that define the input span of the ADC
core. The span of the ADC core is set by this buffer to 2 ×
VREF.
Input Common Mode
The analog inputs of the AD9627-11 are not internally dc biased.
In ac-coupled applications, the user must provide this bias
externally. Setting the device so that VCM = 0.55 × AVDD
is recommended for optimum performance, but the device
functions over a wider range with reasonable performance
(see Figure 44). An on-board common-mode voltage reference
is included in the design and is available from the CML pin.
Optimum performance is achieved when the common-mode
voltage of the analog input is set by the CML pin voltage
(typically 0.55 × AVDD). The CML pin must be decoupled to
ground by a 0.1 μF capacitor, as described in the Applications
Information section.
Differential Input Configurations
Optimum performance is achieved while driving the AD9627-11
in a differential input configuration. For baseband applications,
provide excellent performance and a flexible interface to the ADC.
OBSOLETE
相關PDF資料 |
PDF描述 |
|---|---|
| AD9628BCPZRL7-125 | IC ADC 12BIT 125MSPS 64LFCSP |
| AD9629BCPZ-65 | IC ADC 12BIT 65MSPS 32LFCSP |
| AD9633BCPZRL7-105 | IC ADC 12BIT SRL 105MSPS 48LFCSP |
| AD9634BCPZRL7-170 | IC ADC 12BIT SRL 170MSPS 32LFCSP |
| AD9637BCPZRL7-80 | IC ADC 12BIT SRL 80MSPS 64LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9627ABCPZ-125 | 功能描述:IC ADC 12BIT 1255MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9627ABCPZ-150 | 功能描述:IC ADC 12BIT 150MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD9627ABCPZ-80 | 功能描述:IC ADC 12BIT 80MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9627BCPZ-105 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 105Msps 12-bit Parallel/LVDS 64-Pin LFCSP EP |
| AD9627BCPZ11-105 | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。