參數資料
型號： AD9518-4A/PCBZ
廠商： Analog Devices Inc
文件頁數： 15/64頁
文件大?。?/td> 0K
描述： BOARD EVALUATION FOR AD9518-4A
設計資源： AD9518 Schematics
AD9518 Gerber Files
AD9518-4 BOM
標準包裝： 1
主要目的： 計時，時鐘發生器
嵌入式： 否
已用 IC / 零件： AD9518-4A
主要屬性： 2 輸入，14 輸出，1.6GHz VCO
次要屬性： LVPECL 輸出邏輯
已供物品： 板
AD9518-4
Data Sheet
Rev. B | Page 22 of 64
THEORY OF OPERATION
OPERATIONAL CONFIGURATIONS
The AD9518 can be configured in several ways. These
configurations must be set up by loading the control registers
(see Table 42 and Table 43 through Table 49). Each section
or function must be individually programmed by setting the
appropriate bits in the corresponding control register or registers.
High Frequency Clock Distribution—CLK or External
VCO > 1600 MHz
The AD9518 power-up default configuration has the PLL
powered off and the routing of the input set so that the CLK/CLK
input is connected to the distribution section through the VCO
divider (divide-by-2/divide-by-3/divide-by-4/ divide-by-5/divide-
by-6). This is a distribution-only mode that allows for an external
input up to 2.4 GHz (see
). The maximum frequency that
can be applied to the channel dividers is 1600 MHz; therefore,
higher input frequencies must be divided down before reaching
the channel dividers. This input routing can also be used for lower
input frequencies, but the minimum divide is 2 before the channel
dividers.
When the PLL is enabled, this routing also allows the use of the
PLL with an external VCO or VCXO with a frequency of less than
2400 MHz. In this configuration, the internal VCO is not used
and is powered off. The external VCO/VCXO feeds directly into
the prescaler.
The register settings shown in Table 20 are the default values
of these registers at power-up or after a reset operation. If the
contents of the registers are altered by prior programming after
power-up or reset, these registers can also be set intentionally to
these values.
After the appropriate register values are programmed,
Register 0x232 must be set to 0x01 for the values to take effect.
Table 20. Default Settings of Some PLL Registers
Register
Function
0x010[1:0] = 01b
PLL asynchronous power-down (PLL off ).
0x1E0[2:0] = 010b
Set VCO divider = 4.
0x1E1[0] = 0b
Use the VCO divider.
0x1E1[1] = 0b
CLK selected as the source.
When using the internal PLL with an external VCO, the PLL
must be turned on.
Table 21. Settings When Using an External VCO
Register
Function
0x010[1:0] = 00b
PLL normal operation (PLL on).
0x010 to 0x01D
PLL settings. Select and enable a reference
input; set R, N (P, A, B), PFD polarity, and ICP,
according to the intended loop configuration.
0x1E1[1] = 0b
CLK selected as the source.
An external VCO requires an external loop filter that must be
connected between CP and the tuning pin of the VCO. This
loop filter determines the loop bandwidth and stability of the
PLL. Make sure to select the proper PFD polarity for the VCO
being used.
Table 22. Setting the PFD Polarity
Register
Function
0x010[7] = 0b
PFD polarity positive (higher control voltage
produces higher frequency).
0x010[7] = 1b
PFD polarity negative (higher control
voltage produces lower frequency).
相關PDF資料
PDF描述
BA6920FP-Y IC DRIVER REVERSE MOTOR HSOP25
VE-JTW-EZ-S CONVERTER MOD DC/DC 5.5V 25W
AD9518-2A/PCBZ BOARD EVALUATION FOR AD9518-2A
FCBP110LD1L10 CABLE 10.5GBPS 10M LASERWIRE
ADCLK946/PCBZ KIT EVAL CLK BUFF ADCLK946
相關代理商/技術參數
參數描述
AD9518-4BCPZ 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD9518-4BCPZ-REEL7 制造商:Analog Devices 功能描述:
AD9520 制造商:AD 制造商全稱:Analog Devices 功能描述:Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers
AD9520-0 制造商:AD 制造商全稱:Analog Devices 功能描述:12 LVPECL/24 CMOS Output Clock Generator with Integrated 2.8 GHz VCO
AD9520-0/PCBZ 功能描述:BOARD EVAL AD9520-0 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*