0.8 × f
參數資料
型號： AD9148-M5375-EBZ
廠商： Analog Devices Inc
文件頁數： 51/72頁
文件大小： 0K
描述： BOARD EVAL FOR AD9149, ADL5375
設計資源： AD9148-M5375-EBZ Schematic
AD9148-M5375-EBZ BOM
AD9148-M5375-EBZ Gerber Files
標準包裝： 1
系列： *
Data Sheet
AD9148
Rev. B | Page 55 of 72
When using the fine modulator, the maximum signal bandwidth of
0.8 × fDATA is always achieved.
Updating the Frequency Tuning Word
The frequency tuning word registers are not updated immediately
upon writing as the other configuration registers do. After loading
the FTW registers with the desired values, Bit 2 of Register 0x5A
must transition from 0 to 1 for the new FTW to take effect.
Phase Offset Adjustment
A 16-bit phase offset may be added to the output of the phase
accumulator via the serial port. This static phase adjustment
results in an output signal that is offset by a constant angle
relative to the nominal signal. This allows the user to phase
align the NCO output with some external signal, if necessary.
This can be especially useful when NCOs of multiple AD9148s
are programmed for synchronization. The phase offset allows
for the adjustment of the output timing between the devices.
The static phase adjustment is sourced from the NCO Phase
Offset[15:0] value located in Register 0x58 and Register 0x59.
QUADRATURE PHASE CORRECTION
The purpose of the quadrature phase correction block is to
enable compensation of the phase imbalance of the analog
quadrature modulator following the DAC. If the quadrature
modulator has a phase imbalance, the unwanted sideband
appears with significant energy. Tuning the quadrature
phase adjust value can optimize image rejection in single
sideband radios.
Ordinarily, the I and Q channels have an angle of precisely 90°
between them. The quadrature phase adjustment is used to
change the angle between the I and Q channels. When I Phase
Adj, Bits[9:0] (Register 0x28 and Register 0x29), are set to
1000000000b, the I DAC output moves approximately 1.75°
away from the Q DAC output, creating an angle of 91.75°
between the channels. When I Phase Adj, Bits[9:0] (Register 0x28
and Register 0x29), are set to 0111111111b, the I DAC output
moves approximately 1.75° toward the Q DAC output, creating
an angle of 88.25° between the channels.
Q Phase Adj, Bits[9:0] (Register 2A and Register 2B), work in a
similar fashion. When Q Phase Adj, Bits[9:0] (Register 2A and
Register 2B), are set to 1000000000b, the Q DAC output moves
approximately 1.75° away from the I DAC output, creating an
angle of 91.75° between the channels. When Q Phase Adj[9:0]
is set to 0111111111b, the Q DAC output moves approximately
1.75° toward the I DAC output, creating an angle of 88.25°
between the channels.
Based on these two endpoints, the combined resolution of
the phase compensation register is approximately 3.5°/1024 or
0.00342° per code. When both I Phase Adj, Bits[9:0] (Register 0x28
and Register 0x29), and Q Phase Adj, Bits[9:0] (Register 2A and
Register 2B), are used, the full phase adjustment range is ±3.5°.
DC OFFSET CORRECTION
The dc value of the I data path and the Q data path can be
independently controlled by adjusting I DC Offset, Bits[15:0],
and Q DC Offset, Bits[15:0], values in Register 0x2C through
Register 0x2F. These values are added directly to the data path
values. Care should be taken not to overrange the transmitted
values.
Figure 72 shows how the DAC offset current varies as a function of
I DC Offset, Bits[15:0], and Q DC Offset, Bits[15:0], values. With
the digital inputs fixed at midscale (0x000, twos complement
data format), Figure 72 shows the nominal IOUTxP and IOUTxN
currents as the DC offset value is swept from 0 to 65,535.
Because IOUTxP and IOUTxN are complementary current outputs,
the sum of IOUTxP and IOUTxN is always 20 mA.
0x0000
0x4000
0x8000
0xC000
0xFFFF
5
10
15
20
5
10
15
20
0
DAC OFFSET VALUE
I O
UT
x
N
(mA)
I O
UT
x
P
(
mA)
08910-
131
Figure 72. DAC Output Currents vs. DC Offset Value
DIGITAL GAIN CONTROL
The last block in each datapath is an 8-bit scalar (Register 0x50
and Register 0x51) that can be used for digital gain control. The
IGain Control, Bits[7:0] (Register 0x50), and QGain control,
Bits[7:0] (Register 0x51), values directly scale the samples written to
the IDAC and QDAC, respectively. The bit weighting is MSB = 21
and LSB = 2-6, which yields a multiplier range of 0 to 3.984375.
The scale factor for each data path is calculated as
64
]
0
:
7
[
64
]
0
:
7
[
QGain
or
IGain
r
ScaleFacto =
Take care not to overrange the DAC when using a scale factor
greater than 1.
相關PDF資料
PDF描述
UPB2G181MRD6 CAP ALUM 180UF 400V 20% RADIAL
VE-B64-EY CONVERTER MOD DC/DC 48V 50W
AD9148-M5372-EBZ BOARD EVAL FOR AD9149, ADL5372
AD9737A-EBZ BOARD EVAL FOR AD9737A
MIC2026-1YM IC DISTRIBUTION SW DUAL 8-SOIC
相關代理商/技術參數
參數描述
AD9152BCPZ 功能描述:16 Bit Digital to Analog Converter 2 56-LFCSP-WQ (8x8) 制造商:analog devices inc. 系列:TxDAC+? 包裝:托盤 零件狀態:有效 位數:16 數模轉換器數:2 建立時間:- 輸出類型:Current - Unbuffered 差分輸出:是 數據接口:JESD204B 參考類型:內部 電壓 - 電源，模擬:3.13 V ~ 3.47 V 電壓 - 電源，數字:1.14 V ~ 1.26 V INL/DNL（LSB）:±10，±5 架構:電流源 工作溫度:-40°C ~ 85°C 封裝/外殼:56-WFQFN 裸焊盤，CSP 供應商器件封裝:56-LFCSP-WQ（8x8） 標準包裝:1
AD9152BCPZRL 功能描述:16 Bit Digital to Analog Converter 2 56-LFCSP-WQ (8x8) 制造商:analog devices inc. 系列:TxDAC+? 包裝:帶卷（TR） 零件狀態:有效 位數:16 數模轉換器數:2 建立時間:- 輸出類型:Current - Unbuffered 差分輸出:是 數據接口:JESD204B 參考類型:內部 電壓 - 電源，模擬:3.13 V ~ 3.47 V 電壓 - 電源，數字:1.14 V ~ 1.26 V INL/DNL（LSB）:±10，±5 架構:電流源 工作溫度:-40°C ~ 85°C 封裝/外殼:56-WFQFN 裸焊盤，CSP 供應商器件封裝:56-LFCSP-WQ（8x8） 標準包裝:2,500
AD9152-EBZ 功能描述:AD9152 TxDAC+? Series 16 Bit 2.25G Samples Per Second Digital to Analog Converter (DAC) Evaluation Board 制造商:analog devices inc. 系列:TxDAC+? 零件狀態:有效 DAC 數:2 位數:16 采樣率（每秒）:2.25G 數據接口:SPI 建立時間:- DAC 類型:電流 工作溫度:-40°C ~ 85°C 所含物品:板，線纜 使用的 IC/零件:AD9152 標準包裝:1
AD9152-FMC-EBZ 功能描述:AD9152 TxDAC+? Series 16 Bit 2.25G Samples Per Second Digital to Analog Converter (DAC) Evaluation Board 制造商:analog devices inc. 系列:TxDAC+? 零件狀態:有效 DAC 數:2 位數:16 采樣率（每秒）:2.25G 數據接口:SPI 建立時間:- DAC 類型:電流 工作溫度:-40°C ~ 85°C 所含物品:板，線纜 使用的 IC/零件:AD9152 標準包裝:1
AD9152-M6720-EBZ 功能描述:AD9152 TxDAC+? Series 16 Bit 2.25G Samples Per Second Digital to Analog Converter (DAC) Evaluation Board 制造商:analog devices inc. 系列:TxDAC+? 零件狀態:有效 DAC 數:2 位數:16 采樣率（每秒）:2.25G 數據接口:SPI 建立時間:- DAC 類型:電流 工作溫度:-40°C ~ 85°C 所含物品:板 使用的 IC/零件:AD9152 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*