- 您現在的位置：買賣IC網 > PDF目錄11482 > AD8192ACPZ (Analog Devices Inc)IC SW MUX HDMI/DVI 2:1 56LFCSP PDF資料下載
參數資料
| 型號： | AD8192ACPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SW MUX HDMI/DVI 2:1 56LFCSP |
| 標準包裝： | 1 |
| 功能： | 開關，DVI/HDMI |
| 電路： | 1 x 2:1 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 3.3V，5V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 56-LFCSP-EP（8x8） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD8192
Rev. 0 | Page 24 of 28
the amount of parasitic trace capacitance. An example of the
board stackup is shown in Figure 34.
The AVCC/AVEE (3.3 V) and DVCC/DVEE (3.3 V) supplies
power the core of the AD8192. The VTTI/AVEE supply (3.3 V)
powers the input termination. Similarly, the VTTO/AVEE supply
(3.3 V) powers the output termination. The AMUXVCC/ DVEE
supply (3.3 V to 5 V) powers the auxiliary multiplexer core. The
VREF_COM and VREF_AB supplies determine the logic levels
on the corresponding DDC buses. For example, if the DDC_COM
bus is using 5 V I2C, then VREF_COM should be connected to
+5 V relative to DVEE. If the DDC_AB buses are using 3.3 V
I2C, then VREF_AB should be connected to +5 V relative to DVEE.
PCB DIELECTRIC
LAYER 1: SIGNAL (MICROSTRIP)
SILKSCREEN
PCB DIELECTRIC
LAYER 2: GND (REFERENCE PLANE)
LAYER 3: PWR (REFERENCE PLANE)
LAYER 4: SIGNAL (MICROSTRIP)
W
3W
REFERENCE LAYER
RELIEVED UNDERNEATH
MICROSTRIP
07
05
0-
0
33
In a typical application, connect all pins labeled AVEE or DVEE
directly to ground. Likewise, connect all pins labeled AVCC,
DVCC, VTTI, or VTTO to 3.3 V, and tie Pin AMUXVCC to
5 V. VREF_AB and VREF_COM can be tied to either 3.3 V
or 5 V, depending on the application. The supplies can also be
powered individually, but care must be taken to ensure that
each stage of the AD8192 is powered correctly.
Power Supply Bypassing
Figure 34. Example Board Stackup
The AD8192 requires minimal supply bypassing. When
powering the supplies individually, place a 0.01 μF capacitor
between each 3.3 V supply pin (AVCC, DVCC, VTTI, and
VTTO) and ground, and place a 0.1 μF capacitor between each
additional supply pin (AMUXVCC, VREF_AB, and VREF_COM)
and ground to filter out supply noise. Generally, place bypass
capacitors near the power pins and connect them directly to the
relevant supplies (without long intervening traces). For example, to
improve the parasitic inductance of the power supply decoupling
capacitors, minimize the trace length between capacitor landing
pads and the vias.
HPD is a dc signal presented by a sink to a source to indicate
that the source EDID is available for reading. The placement of
this signal is not critical, but it should be routed as directly as
possible.
When the AD8192 is powered up, the DDC/CEC inputs of the
selected channel are actively buffered and routed to the outputs,
and the unselected auxiliary inputs are high impedance. When
the AD8192 is powered off, all DDC/CEC inputs are placed in a
high impedance state. This prevents contention on the DDC
bus, enabling a design to include an EDID in front of the AD8192.
Power Supplies
In applications where the AD8192 is powered by a single 3.3 V
supply, it is recommended to use two reference supply planes
and bypass the 3.3 V reference plane to the ground reference
plane with one 220 pF, one 1000 pF, two 0.01 μF, and one 4.7 μF
capacitors. If the AMUXVCC, VREF_AB, and VREF_COM
connections are all powered by a single 5 V supply, it is sufficient
to use a single 0.1 μF to bypass all three connections. The capa-
citors should via down directly to the supply planes and be
placed within a few centimeters of the AD8192.
The AD8192 has five separate power supplies referenced to
two separate grounds. The supply/ground pairs are
AVCC/AVEE
VTTI/AVEE
VTTO/AVEE
DVCC/DVEE
AMUXVCC/DVEE
VREF_AB/DVEE
VREF_COM/DVEE
相關PDF資料 |
PDF描述 |
|---|---|
| PIC18F4321T-I/PT | IC PIC MCU FLASH 4KX16 44TQFP |
| ADG408BNZ | IC MULTIPLEXER 8X1 16DIP |
| PIC32MX220F032DT-V/PT | IC MCU 32BIT 32KB FLASH 44-TQFP |
| GRM21BC80J106ME19L | CAP CER 10UF 6.3V 20% X6S 0805 |
| PIC24FV16KA304T-I/PT | MCU 16KB FLASH 2KB RAM 44TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8192ACPZ-RL7 | 功能描述:IC SW MUX HDMI/DVI 2:1 56LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
| AD8192-EVALZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:2:1 HDMI/DVI Switch with Equalization and DDC/CEC Buffers |
| AD8192XCPZ | 功能描述:IC SW MUX HDMI/DVI 2:1 56LFCSP 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:上次購買時間 類型:視頻開關 應用:HDTV，投影儀，機頂盒 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商器件封裝:56-LFCSP-VQ（8x8） 標準包裝:1 |
| AD8192XCPZ-RL | 功能描述:IC SW MUX HDMI/DVI 2:1 56LFCSP 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:上次購買時間 類型:視頻開關 應用:HDTV，投影儀，機頂盒 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商器件封裝:56-LFCSP-VQ（8x8） 標準包裝:1 |
| AD8193 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Buffered 2:1 TMDS Switch |
發布緊急采購，3分鐘左右您將得到回復。