- 您現在的位置：買賣IC網 > PDF目錄10133 > AD7983BRMZ-RL7 (Analog Devices Inc)IC ADC 16BIT 1.33MSPS 10MSOP PDF資料下載
參數資料
| 型號： | AD7983BRMZ-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 1.33MSPS 10MSOP |
| 標準包裝： | 1,000 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 1.33M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 12mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，單極 |
AD7983
Rev. A | Page 23 of 24
APPLICATION HINTS
LAYOUT
The printed circuit board (PCB) that houses the AD7983
should be designed so that the analog and digital sections are
separated and confined to certain areas of the board. The pinout of
the AD7983, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Avoid running digital lines under the device because these couple
noise onto the die, unless a ground plane under the AD7983 is
used as a shield. Fast switching signals, such as CNV or clocks,
should never run near analog signal paths. Crossover of digital
and analog signals should be avoided.
At least one ground plane should be used. It can be common or
split between the digital and analog section. In the latter case,
the planes should be joined underneath the AD7983.
The AD7983 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, ideally right up against, the REF and
GND pins and connecting them with wide, low impedance traces.
Finally, the AD7983 power supplies, VDD and VIO, should be
decoupled with ceramic capacitors, typically 100 nF, placed
close to the AD7983 and connected using short and wide traces
to provide low impedance paths and to reduce the effect of
glitches on the power supply lines.
An example of a layout following these rules is shown in
EVALUATING THE PERFORMANCE OF THE AD7983
Other recommended layouts for the AD7983 are outlined
in the documentation of the evaluation board for the AD7983
(EVAL-AD7983CBZ). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-CONTROL BRD.
AD7983
0
69
74
-02
4
Figure 38. Example Layout of the AD7983 (Top Layer)
06
97
4-
02
5
Figure 39. Example Layout of the AD7983 (Bottom Layer)
相關PDF資料 |
PDF描述 |
|---|---|
| IDT7202LA20P | IC FIFO ASYNCH 1KX9 20NS 28DIP |
| ADM237LJNZ | IC TXRX RS-232 5:3 5V LP 24-DIP |
| AD7983BCPZ-RL | IC ADC 16BIT 1.33MSPS 10LFCSP |
| LT1032CSW | IC LINE DRIVR LOWPWR QUAD 16SOIC |
| IDT7202LA25TPI | IC FIFO ASYNCH 1KX9 25NS 28DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7984 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 1.33 MSPS PulSAR 10.5 mW ADC in MSOP/QFN |
| AD79841 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7984BCPZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 1.33 MSPS PulSAR 10.5 mW ADC in MSOP/QFN |
| AD7984BCPZ-R2 | 制造商:Analog Devices 功能描述: |
| AD7984BCPZ-RL | 功能描述:IC ADC 18BIT 1.33MSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。