- 您現在的位置：買賣IC網 > PDF目錄10133 > AD7983BRMZ-RL7 (Analog Devices Inc)IC ADC 16BIT 1.33MSPS 10MSOP PDF資料下載
參數資料
| 型號： | AD7983BRMZ-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 1.33MSPS 10MSOP |
| 標準包裝： | 1,000 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 1.33M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 12mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，單極 |
AD7983
Rev. A | Page 19 of 24
CS MODE, 4-WIRE WITHOUT BUSY INDICATOR
This mode is usually used when multiple AD7983s are
connected to an SPI-compatible digital host.
A connection diagram example using two AD7983s is shown in
With SDI high, a rising edge on CNV initiates a conversion,
selects the CS mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback (if SDI and CNV are low, SDO is
driven low). Prior to the minimum conversion time, SDI can be
used to select other SPI devices, such as analog multiplexers,
but SDI must be returned high before the minimum conversion
time elapses and then held high for the maximum conversion
time to avoid the generation of the busy signal indicator.
When the conversion is complete, the AD7983 enters the
acquisition phase and goes into standby mode. Each ADC result
can be read by bringing its SDI input low, which consequently
outputs the MSB onto SDO. The remaining data bits are then
clocked by subsequent SCK falling edges. The data is valid on
both SCK edges. Although the rising edge can be used to capture
the data, a digital host using the SCK falling edge allows a faster
reading rate provided it has an acceptable hold time. After the
16th SCK falling edge or when SDI goes high, whichever is
earlier, SDO returns to high impedance and another AD7983
can be read.
DIGITAL HOST
CONVERT
CS2
CS1
CLK
DATA IN
AD7983 SDO
SDI
CNV
SCK
AD7983 SDO
SDI
CNV
SCK
06
97
4-
01
6
Figure 30. CS Mode, 4-Wire Without Busy Indicator Connection Diagram
tCONV
tCYC
ACQUISITION
tACQ
tSCK
tSCKH
tSCKL
CONVERSION
SCK
CNV
tSSDICNV
tHSDICNV
SDO
D15
D13
D14
D1
D0
D15
D14
D1
D0
tHSDO
tEN
1
2
3
14
15
16
17
18
30
31
32
tDSDO
tDIS
SDI(CS1)
SDI(CS2)
06
97
4-
0
17
Figure 31. CS Mode, 4-Wire Without Busy Indicator Serial Interface Timing
相關PDF資料 |
PDF描述 |
|---|---|
| IDT7202LA20P | IC FIFO ASYNCH 1KX9 20NS 28DIP |
| ADM237LJNZ | IC TXRX RS-232 5:3 5V LP 24-DIP |
| AD7983BCPZ-RL | IC ADC 16BIT 1.33MSPS 10LFCSP |
| LT1032CSW | IC LINE DRIVR LOWPWR QUAD 16SOIC |
| IDT7202LA25TPI | IC FIFO ASYNCH 1KX9 25NS 28DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7984 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 1.33 MSPS PulSAR 10.5 mW ADC in MSOP/QFN |
| AD79841 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7984BCPZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 1.33 MSPS PulSAR 10.5 mW ADC in MSOP/QFN |
| AD7984BCPZ-R2 | 制造商:Analog Devices 功能描述: |
| AD7984BCPZ-RL | 功能描述:IC ADC 18BIT 1.33MSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。