參數資料
型號: AD7942BRMZ
廠商: Analog Devices Inc
文件頁數: 4/24頁
文件大小: 0K
描述: IC ADC 14BIT 250KSPS 10-MSOP
標準包裝: 50
系列: PulSAR®
位數: 14
采樣率(每秒): 250k
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 1.25mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-MSOP
包裝: 管件
輸入數目和類型: 1 個偽差分,單極
產品目錄頁面: 780 (CN2011-ZH PDF)
配用: EVAL-AD7942CB-ND - BOARD EVALUATION FOR AD7942
AD7942
Rev. B | Page 12 of
24
TERMINOLOGY
Linearity Error or Integral Nonlinearity Error (INL)
Linearity error refers to the deviation of each individual code
from a line drawn from negative full scale through positive full
scale. The point used as negative full scale occurs LSB before
the first code transition. Positive full scale is defined as a level
1 LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Offset Error
The first transition should occur at a level LSB above analog
ground (152.6 μV for the 0 V to 5 V range). The offset error is
the deviation of the actual transition from that point.
Gain Error
The last transition (from 111...10 to 111...11) should occur
for an analog voltage 1 LSB below the nominal full scale
(4.999542 V for the 0 V to 5 V range). The gain error is the
deviation of the actual level of the last transition from the
ideal level after the offset has been adjusted out.
Spurious-Free Dynamic Range (SFDR)
The difference, in decibels, between the rms amplitude of the
input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD by the following formula and is
expressed in bits as follows:
ENOB = (SINADdB 1.76)/6.02
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and
is expressed in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
Signal-to-Noise and Distortion Ratio (SINAD)
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in decibels.
Aperture Delay
Aperture delay is a measure of the acquisition performance and
is the time between the rising edge of the CNV input and when
the input signal is held for a conversion.
Transient Response
The time required for the ADC to accurately acquire its input
after a full-scale step function was applied.
相關PDF資料
PDF描述
ISL4223EIRZ IC TXRX 2TX/2RX 3V RS-232 20-QFN
DP83848CVV/NOPB IC TXRX ETHERNET PHYTER 48-LQFP
VI-21W-MX CONVERTER MOD DC/DC 5.5V 75W
VI-2TH-IX-B1 CONVERTER MOD DC/DC 52V 75W
AD7924BRUZ IC ADC 12BIT 4CH W/SEQ 16TSSOP
相關代理商/技術參數
參數描述
AD7942BRMZ1 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 250 kSPS PulSAR, Pseudo Differential ADC in MSOP/QFN
AD7942BRMZ-RL7 功能描述:IC ADC 14BIT 250KSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7942BRMZ-RL71 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 250 kSPS PulSAR, Pseudo Differential ADC in MSOP/QFN
AD7943 制造商:AD 制造商全稱:Analog Devices 功能描述:+3.3 V/+5 V Multiplying 12-Bit DACs
AD7943AN-B 制造商:Rochester Electronics LLC 功能描述:SERIAL 12-BIT IOUT DAC-IC - Bulk