- 您現在的位置：買賣IC網 > PDF目錄375240 > AD7927 (Analog Devices, Inc.) 8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP PDF資料下載
參數資料
| 型號： | AD7927 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP |
| 中文描述： | 8通道，200 kSPS的，12位序列ADC的20引腳TSSOP |
| 文件頁數： | 12/21頁 |
| 文件大?。?/td> | 461K |
| 代理商： | AD7927 |
REV. 0
–12–
AD7927
POWER-ON
DUMMY CONVERSION
DIN = ALL 1s
DIN: WRITE TO CONTROL REGISTER,
WRITE BIT = 1,
SELECT CODING, RANGE, AND POWER MODE.
SELECT CHANNEL A2–A0 FOR CONVERSION.
SEQ = 1 SHADOW = 1
DOUT: CONVERSION RESULT FROM CHANNEL 0
CONTINUOUSLY CONVERTS ON A CONSECUTIVE
SEQUENCE OF CHANNELS FROM CHANNEL 0 UP
TO AND INCLUDING THE PREVIOUSLY SELECTED
A2–A0 IN THE CONTROL REGISTER
WRITE BIT = 0
CONTINUOUSLY CONVERTS ON THE SELECTED
SEQUENCE OF CHANNELS BUT WILL ALLOW
RANGE, CODING AND SO ON, TO CHANGE IN THE
CONTROL REGISTER WITHOUT INTERRUPTING
THE SEQUENCE, PROVIDED SEQ = 1 SHADOW = 0
WRITE BIT = 1,
SEQ = 1,
SHADOW = 0
CS
CS
CS
Figure 4. SEQ Bit = 1, SHADOW Bit = 1 Flowchart
CIRCUIT INFORMATION
The AD7927 is a high speed, 8-channel, 12-bit, single supply,
A/D converter. The part can be operated from a 2.7 V to 5.25 V
supply. When operated from either a 5 V or 3 V supply, the AD7927
is capable of throughput rates of 200 kSPS. The conversion time
may be as short as 800 ns when provided with a 20 MHz clock.
The AD7927 provides the user with an on-chip track-and-hold,
A/D converter, and a serial interface housed in a 20-lead TSSOP
package. The AD7927 has eight single-ended input channels
with a channel sequencer, allowing the user to select a channel
sequence through which the ADC can cycle with each consecu-
tive
CS
falling edge. The serial clock input accesses data from
the part, controls the transfer of data written to the ADC, and
provides the clock source for the successive-approximation A/D
converter. The analog input range for the AD7927 is 0 V to
REF
IN
or 0 V to 2
￥
REF
IN
, depending on the status of Bit 1 in
the Control Register. For the 0 to 2
￥
REF
IN
range, the part
must be operated from a 4.75 V to 5.25 V supply.
The AD7927 provides flexible power management options to
allow the user to achieve the best power performance for a given
throughput rate. These options are selected by programming the
Power Management bits, PM1 and PM0, in the Control Register.
CONVERTER OPERATION
The AD7927 is a 12-bit successive approximation analog-to-
digital converter based around a capacitive DAC. The AD7927
can convert analog input signals in the range 0 V to REF
IN
or 0 V
to 2
￥
REF
IN
. Figures 5 and 6 show simplified schematics of the
ADC. The ADC is comprised of Control Logic, SAR, and a
Capacitive DAC that are used to add and subtract fixed amounts
of charge from the sampling capacitor to bring the comparator
back into a balanced condition. Figure 5 shows the ADC during
its acquisition phase. SW2 is closed and SW1 is in position A.
The comparator is held in a balanced condition and the sampling
capacitor acquires the signal on the selected V
IN
channel.
V
IN
0
V
IN
7
AGND
A
B
SW1
SW2
COMPARATOR
CONTROL
LOGIC
CAPACITIVE
DAC
4k
Figure 5. ADC Acquisition Phase
When the ADC starts a conversion (see Figure 6), SW2 will
open and SW1 will move to position B, causing the comparator
to become unbalanced. The Control Logic and the Capacitive
DAC are used to add and subtract fixed amounts of charge
from the sampling capacitor to bring the comparator back into a
balanced condition. When the comparator is rebalanced, the
conversion is complete. The Control Logic generates the ADC
output code. Figures 8 and 9 show the ADC transfer functions.
V
IN
0
.
.
V
IN
7
AGND
A
B
SW1
SW2
COMPARATOR
CONTROL
LOGIC
4k
CAPACITIVE
DAC
Figure 6. ADC Conversion Phase
Analog Input
Figure 7 shows an equivalent circuit of the analog input structure
of the AD7927. The two diodes D1 and D2 provide ESD pro-
tection for the analog inputs. Care must be taken to ensure that
the analog input signal never exceeds the supply rails by more
than 300 mV. This will cause these diodes to become forward
biased and start conducting current into the substrate. 10 mA is
the maximum current these diodes can conduct without causing
irreversible damage to the part. The capacitor C1 in Figure 7 is
typically about 4 pF and can primarily be attributed to pin capaci-
tance. The resistor R1 is a lumped component made up of the on
resistance of a switch (track-and-hold switch) and also includes
the on resistance of the input multiplexer. The total resistance is
typically about 400
W
. The capacitor C2 is the ADC sampling
capacitor and has a capacitance of 30 pF typically. For ac appli-
cations, removing high frequency components from the analog
input signal is recommended by use of an RC low-pass filter on
the relevant analog input pin. In applications where harmonic
distortion and signal to noise ratio are critical, the analog input
should be driven from a low impedance source. Large source
impedances will significantly affect the ac performance of the ADC.
This may necessitate the use of an input buffer amplifier. The
choice of the op amp will be a function of the particular application.
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum source
impedance will depend on the amount of total harmonic distortion
(THD) that can be tolerated. The THD will increase as the source
impedance increases, and performance will degrade. (See TPC 5.)
V
IN
C1
4pF
C2
30pF
R1
D1
D2
AV
DD
CONVERSION PHASE: SWITCH OPEN
TRACK PHASE: SWITCH CLOSED
Figure 7. Equivalent Analog Input Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| AD7927BRU | 8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP |
| AD7934 | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| AD7934BRU | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| AD7933 | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| AD7933BRU | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7927BRU | 功能描述:IC ADC 12BIT 8CH 200KSPS 20TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7927BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 20-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 200KSPS 12-BIT SERL 20TSSOP - Tape and Reel |
| AD7927BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 20-Pin TSSOP T/R |
| AD7927BRUZ | 功能描述:IC ADC 12BIT 8CH 200KSPS 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7927BRUZ | 制造商:Analog Devices 功能描述:IC 12BIT ADC SMD 7927 TSSOP20 |
發布緊急采購，3分鐘左右您將得到回復。