- 您現在的位置：買賣IC網 > PDF目錄375240 > AD7927 (Analog Devices, Inc.) 8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP PDF資料下載
參數資料
| 型號： | AD7927 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP |
| 中文描述： | 8通道，200 kSPS的，12位序列ADC的20引腳TSSOP |
| 文件頁數： | 11/21頁 |
| 文件大?。?/td> | 461K |
| 代理商： | AD7927 |
REV. 0
AD7927
–11–
POWER-ON
DUMMY CONVERSION
DIN = ALL 1s
DIN: WRITE TO CONTROL REGISTER,
WRITE BIT = 1,
SELECT CODING, RANGE, AND POWER MODE.
SELECT CHANNEL A2–A0 FOR CONVERSION.
SEQ = SHADOW = 0
DOUT: CONVERSION RESULT FROM PREVIOUSLY
SELECTED CHANNEL A2–A0.
DIN: WRITE TO CONTROL REGISTER,
WRITE BIT = 1,
SELECT CODING, RANGE, AND POWER MODE.
SELECT A2–A0 FOR CONVERSION.
SEQ = SHADOW = 0
WRITE BIT = 1,
SEQ = SHADOW = 0
CS
CS
Figure 2. SEQ Bit = 0, SHADOW Bit = 0 Flowchart
Figure 2 reflects the traditional operation of a multichannel ADC,
where each serial transfer selects the next channel for conversion.
In this mode of operation, the sequencer function is not used.
Figure 3 shows how to program the AD7927 to continuously
convert on a particular sequence of channels. To exit this mode
of operation and revert back to the traditional mode of operation
of a multichannel ADC (as outlined in Figure 2), ensure that the
WRITE bit = 1 and the SEQ = SHADOW = 0 on the next serial
transfer. Figure 4 shows how a sequence of consecutive chan-
nels can be converted on without having to program the Shadow
Register or write to the part on each serial transfer. Again, to exit
this mode of operation and revert back to the traditional mode
of operation of a multichannel ADC (as outlined in Figure 2),
ensure the WRITE bit = 1 and the SEQ = SHADOW = 0 on
the next serial transfer.
CS
POWER-ON
DUMMY CONVERSION
DIN = ALL 1s
DIN: WRITE TO CONTROL REGISTER,
WRITE BIT = 1,
SELECT CODING, RANGE, AND POWER MODE.
SELECT CHANNEL A2–A0 FOR CONVERSION.
SEQ = 0 SHADOW = 1
DOUT: CONVERSION RESULT FROM PREVIOUSLY
SELECTED CHANNEL A2–A0.
DIN: WRITE TO SHADOW REGISTER, SELECTING
WHICH CHANNELS TO CONVERT ON; CHANNELS
SELECTED NEED NOT BE CONSECUTIVE CHANNELS
WRITE BIT = 1,
SEQ = 1,
SHADOW = 0
CS
CS
WRITE BIT = 0
WRITE BIT = 1
SEQ = 1 SHADOW = 0
CONTINUOUSLY
CONVERTS ON THE
SELECTED
SEQUENCE OF
CHANNELS
CONTINUOUSLY
CONVERTS ON THE
SELECTED
SEQUENCE OF
CHANNELS BUT
WILL ALLOW RANGE,
CODING, AND SO ON,
TO CHANGE IN THE
CONTROL REGISTER
WITHOUT INTERRUPT-
ING THE SEQUENCE,
PROVIDED SEQ = 1
SHADOW = 0
WRITE BIT = 0
WRITE BIT = 0
Figure 3. SEQ Bit = 0, SHADOW Bit = 1 Flowchart
SHADOW REGISTER
The Shadow Register on the AD7927 is a 16-bit, write-only
register. Data is loaded from the DIN pin of the AD7927 on the
falling edge of SCLK. The data is transferred on the DIN line at
the same time that a conversion result is read from the part. This
requires 16 serial clock falling edges for the data transfer. The
information is clocked into the Shadow Register, provided that the
SEQ and SHADOW bits were set to 0,1, respectively, in the
previous write to the Control Register. MSB denotes the first bit
in the data stream. Each bit represents an analog input from
Channel 0 to Channel 7. Through programming the Shadow
Register, two sequences of channels may be selected, through
which the AD7927 will cycle with each consecutive conversion
after the write to the Shadow Register. Sequence One will be
performed first and then Sequence Two. If the user does not
wish to preform a second sequence option, then all 0s must be
written to the last eight LSBs of the Shadow Register. To select
a sequence of channels, the associated channel bit must be set for
each analog input. The AD7927 will continuously cycle through
the selected channels in ascending order, beginning with the
lowest channel, until a write operation occurs (i.e., the WRITE bit
is set to 1) with the SEQ and SHADOW bits configured in any
way except 1,0. (See Table IV.) The bit functions are outlined
in Table V.
Table V. Shadow Register Bit Functions
MSB
V
IN
0
LSB
V
IN
7
V
IN
1
V
IN
2
V
IN
3
V
IN
4
V
IN
5
V
IN
6
V
IN
7
V
IN
0
V
IN
1
V
IN
2
V
IN
3
V
IN
4
V
IN
5
V
IN
6
------------------SEQUENCE ONE-------------------------------------------------------SEQUENCE TWO-----------------------
相關PDF資料 |
PDF描述 |
|---|---|
| AD7927BRU | 8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP |
| AD7934 | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| AD7934BRU | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| AD7933 | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| AD7933BRU | 4-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7927BRU | 功能描述:IC ADC 12BIT 8CH 200KSPS 20TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7927BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 20-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 200KSPS 12-BIT SERL 20TSSOP - Tape and Reel |
| AD7927BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 20-Pin TSSOP T/R |
| AD7927BRUZ | 功能描述:IC ADC 12BIT 8CH 200KSPS 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7927BRUZ | 制造商:Analog Devices 功能描述:IC 12BIT ADC SMD 7927 TSSOP20 |
發布緊急采購，3分鐘左右您將得到回復。