- 您現在的位置：買賣IC網 > PDF目錄1984 > AD7877WACPZ-REEL7 (Analog Devices Inc)IC CTRLR TOUCH SCREEN 32LFCSP PDF資料下載
參數資料
| 型號： | AD7877WACPZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/45頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTRLR TOUCH SCREEN 32LFCSP |
| 標準包裝： | 1 |
| 類型： | 電阻 |
| 觸摸面板接口： | 4 線 |
| 輸入數/鍵： | 1 TSC |
| 分辨率（位）： | 12 b |
| 評估套件： | 可供 |
| 數據接口： | 串行，SPI? |
| 數據速率/采樣率 (SPS，BPS)： | 125k |
| 電壓基準： | 外部，內部 |
| 電源電壓： | 2.7 V ~ 5.25 V |
| 電流 - 電源： | 1µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ（5x5） |
| 包裝： | 標準包裝 |
| 其它名稱： | AD7877WACPZ-REEL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
Data Sheet
AD7877
Rev. D | Page 17 of 44
It is only during the sample or acquisition phase of the ADC
operation of the AD7877 that noise from the LCD screen has an
effect on the ADC measurements. During the hold or
conversion phase, the noise has no effect, because the voltage at
the input of the ADC has already been acquired. Therefore, to
minimize the effect of noise on the touch screen measurements,
the ADC acquisition phase should be halted.
The LCD control signal should be applied to the STOPACQ pin.
To ensure that acquisition never occurs during the noisy period
when the LCD signal is active, the AD7877 monitors this signal.
No acquisitions take place when the control signal is active. Any
acquisition that is in progress when the signal becomes active is
aborted and restarts when the signal becomes inactive again.
To accommodate signals of different polarities on the
STOPACQ pin, a user-programmable register bit is used to
indicate whether the signal is active high or low. The POL bit
is Bit 3 in Control Register 2, Address 0x02. Setting POL to 1
indicates that the signal on STOPACQ is active high; setting
POL to 0 indicates that it is active low. POL defaults to 0 on
power-up. To disable monitoring of STOPACQ, the pin should
be tied low if POL = 1, or tied high if POL = 0. Under no
circumstances should the pin be left floating.
The signal on STOPACQ has no effect while the ADC is in
conversion mode, or during the first conversion delay time.
(See the Control Registers section for details on the first
conversion delay.)
When enabled, the STOPACQ monitoring function is imple-
mented on all input channels to the ADC: AUX1, AUX2, BAT1,
BAT2, TEMP1, and TEMP2, as well as on the touch screen
input channels.
TEMPERATURE MEASUREMENT
Two temperature measurement options are available on the
AD7877: the single conversion method and the differential
conversion method. The single conversion method requires
only a single measurement on ADC Channel 1000b. Whereas
differential conversion requires two measurements, one on
ADC Channel 1000b and a second on ADC Channel 1001b.
The results are stored in the results registers with Address 11000b
(TEMP1) and Address 11001b (TEMP2). The AD7877 does not
provide an explicit output of the temperature reading; the
system must perform some external calculations. Both methods
are based on an on-chip diode measurement.
Single Conversion Method
The single conversion method makes use of the fact that the
temperature coefficient of a silicon diode is approximately
2.1 mV/°C. However, this small change is superimposed on
the diode forward voltage, which can have a wide tolerance. It
is, therefore, necessary to calibrate by measuring the diode
voltage at a known temperature to provide a baseline from
which the change in forward voltage with temperature can be
measured. This method provides a resolution of approximately
0.3°C and a predicted accuracy of ±2.5°C.
The temperature limit comparison is performed on the result in
the TEMP1 results register, which is simply the measurement of
the diode forward voltage. The values programmed into the high
and low limits should be referenced to the calibrated diode for-
ward voltage to make accurate limit comparisons. An example
is shown in the Limit Comparison section.
Differential Conversion Method
The differential conversion method is a 2-point measurement.
The first measurement is performed with a fixed bias current
into a diode (when the TEMP1 channel is selected), and the
second measurement is performed with a fixed multiple of the
bias current into the same diode (when the TEMP2 channel is
selected). The voltage difference in the diode readings is pro-
portional to absolute temperature and is given by the following
formula:
VBE = (kT/q) × (ln N)
(4)
where:
VBE represents the diode voltage.
N is the bias current multiple (typical value for AD7877 = 120).
k is Boltzmann’s constant.
q is the electron charge.
This method provides a resolution of approximately 1.6°C, and
a guaranteed accuracy of ±4°C without calibration. Determina-
tion of the N value on a part-by-part basis improves accuracy.
Assuming a current multiple of 120, which is a typical value
for the AD7877, taking Boltzmann’s constant, k = 1.38054 ×
1023 electrons V/°K, the electron charge q = 1.602189 × 1019,
then T, the ambient temperature in Kelvin, would be calculated
as follows:
VBE = (kT/q) × (ln N)
T°k = (VBE × q)/(k × ln N)
= (VBE × 1.602189 × 1019)/(1.38054 × 1023 × 4.65)
T°C = 2.49 × 120 × VBE 273
VBE is calculated from the difference in readings from the first
conversion to the second conversion. The user must perform
the calculations to get VBE, and then calculate the temperature
value in degrees. Figure 33 shows a block diagram of the
temperature measurement circuit.
03796-
0
1
TEMP1
TEMP2
MUX
ADC
I
VBE
I20 × I
Figure 33. Block Diagram of Temperature Measurement Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| AD7878KPZ | IC ADC 12BIT W/DSP INT 28-PLCC |
| AD7880CR | IC ADC 12BIT MONO LP 24-SOIC |
| AD7884BQ | IC ADC 16BIT SAMPLING HS 40-CDIP |
| AD7886JD | IC ADC 12BIT SAMPLING HS 28-CDIP |
| AD7887ARZ-REEL | IC ADC 12BIT 2CHAN SRL 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7878 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878AQ | 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk |
| AD7878BQ | 功能描述:IC ADC 12BIT W/DSP INT 28-CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| AD7878JN | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin PDIP W 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk 制造商:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878JNZ | 功能描述:IC ADC 12BIT W/DSP INT 28-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。